Wfly ET08 Скачать руководство пользователя страница 51

Страница: 51 / 84

TRIM SETTING

Interface path: HOME/MON.→ [GENERAL MENU] → [TRIM SETTING].

In this function, you can set the amount of digital trim and the action mode, and you can select the trim

step movement under each condition, or trim the individual movement under each condition. (For example,
hover and stunt can be trimmed separately.)

Step: Adjustable travel 1-250, the default step value is 40 (the amount of motion change per trimming).

T1-T4:

Link: For example, after T1 is linked, the channel assigned by the corresponding T1 will follow the action.

Switch: INH, 2 POS, 3 POS, the default "INH", control the corresponding trimming dynamic display of the

main interface. Inhibit, the main interface hides the corresponding trim switch. 2, 3 POS, the main interface
display corresponding trimming switch

Condition: Group, single, default "group". Group modes: The same trimming data is reﬂected in all ﬂight

conditions. Single mode: Individual trimming adjustments are possible under each condition.

GENERAL MENU

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Бренды по названию

Популярные бренды