Wfly ET08 страница 37 Скачать руководство пользователя

Страница: 37 / 84

PPM/W.BUS

* Diﬀerent receivers, diﬀerent ports.

Interface path: HOME/MON.→ [LINKAGE SETTING] → [PPM/W.BUS]

Switch the receiver PPM/W.BUS output mode.

W.BUS mode is compatible with S.BUS signal.

PPM mode. The 6th port of the RF206S outputs with

a standard 4096 resolution and 8 channel PPM signal.

* After the switch is completed, the receiver status lamp can be used to check whether it is

successful.(refer to receiver operating status table).

Switching the 6th port mode of the receiver:

1 When the receiver is connected, click the mode button to switch the mode, click the function title in the

upper left corner to return to the previous menu and save the changes.

2 Please refer to the “Receiver manual instruction” section (page 15) “PPM/W.BUS Interface Operation

Mode Selection”, and the receiver can also directly switch the 6-port mode.

LINKAGE SETTING

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды