Wfly ET08 Скачать руководство пользователя страница 45

Страница: 45 / 84

GENERAL MENU

MONITOR

Operating Mode:

- "NEUT" mode: Neutral,all channels, the rudder opportunity is ﬁxed at the midpoint stroke position.
- "MOV" mode: Movement,all channels, rudder opportunities repeatedly.

This interface can be used to understand the servo output of each channel and conﬁrm the servo action.

Interface path: HOME/MON. → [GENERAL MENU] → [MONITOR]

It can also perform the servo test, such as “stroke” and “Midpoint Test”.

- OFF: The default item displays the real-time output position of all current channels.

Throttle: The throttle channel is closed by default, avoiding the throttle channel action output in case of

causing danger.

Touch & hold
Left

HOME/MON.

Key

Can bring up the monitor
interface directly

OFF

NEUT

MOV

2 Test of the end and midpoint of the servo stroke.

1 Servo action (channel) output real-time dynamic viewing.

2 Dynamic mode: All channels (servo) are cycled back and forth between the two ends, and the stroke

adjustment is made, so that it is possible to adjust whether the magnitude of the motion of the servo of each
channel is suitable for the model.

Monitor Application:

1 Midpoint mode: All channels (servo) are at the neutral point, and the midpoint of the servo of each

channel can be ﬁne-tuned, thereby ﬁne-tuning the model.

Servo test function:

DANGER

Never use the servo test mode

when the motor is connected or the

engine is in the start state. (It is very dangerous to
cause the propeller or rotor to rotate.)

WARNING

In dynamic mode, each rudder

moves at an angle set by the

rudder angle, so do not perform this test while
connected to the body. (It may cause damage to the
servo or connector or even the body.).

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Бренды по названию

Популярные бренды