Wfly ET08 страница 53 Скачать руководство пользователя | Manualshive

Страница: 53 / 84

background image

CHANNEL DELAY

This function is mainly used for realistic actions, such as retracting the undercarriage (reducing the

response speed of the output channel), setting the stroke to 0 to 100, and the default is 0 (corresponding to
the delay time of the channel stick position from one end to the other end is the set time).

Interface path: HOME/MON. → [GENERAL MENU] → [CHANNEL DELAY]

The larger the value displayed on the interface, the larger the delay and the slower the output of the

action.

Default "0", no delay
Maximum value "100",Maximum delay

Used to enable and disable the delay function

Customize any switch, knob, etc.

53

GENERAL MENU

«
...
51
52
53
54
55
...
»

Содержание ET08





















































































Отзывы:

Нет отзывов

Похожие инструкции для ET08

Бренд: Xantech Страницы: 47

Бренд: Comtek Страницы: 18

Бренд: M-system Страницы: 2

A25C SPORT 66 USA

Бренд: Icom Страницы: 4

Бренд: Covid Страницы: 12

Бренд: Ten-Tec Страницы: 2

FMT 380 BT CHARGE

Бренд: Hyundai Страницы: 24

Бренд: Vaisala Страницы: 89

Бренд: Naxa Страницы: 5

Бренд: Mobrey Страницы: 180

Бренд: Magtech Страницы: 35

Бренд: M-system Страницы: 3

Бренд: Dillinger Labs Страницы: 30

Mini-Com HH-156-D1

Бренд: Wilson Electronics Страницы: 25

Бренд: Hendricks QRP Kits Страницы: 37

Бренд: Technisonic Industries Limited Страницы: 21

Бренд: Texas Instruments Страницы: 66

Бренд: Shearwater Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды