Wfly ET08 Скачать руководство пользователя

Страница: 11 / 84

Switch conﬁguration and model types

The Travel Of Antenna Direction Adjustment

SA: Short lever 2 positions (user-deﬁned)

Power LED: Left, power indicator light, red
RF LED: Right, RF indicator light, blue.

POWER: Click and hold for 3 seconds to open/shut down;

SB: Long lever 3 positions (user-deﬁned)

SD: Short lever 2 positions (user-deﬁned)

SC: Long lever 3 positions (user-deﬁned)

LD/RD: Rotary Knob(User-deﬁned)

TRAINER: Trainer port

5-way button: Move the cursor button up and down or left and right, middle button for conﬁrmation(Long

press to reset).

T1-T4:Trim,(User-deﬁned)

EXIT/LOCK: Exit/Lock key, slightly click to exist, press and hold to lock the screen.

HOME/MON.: Home/Monitor key, slightly click home, press and hold monitor.

Mandatory

Before Use

Transmitter faces upside
As the picture shows

Receiver faces upside
As the picture shows

Strong
signal acquisition

Weak
signal acquisition

Avoid metal objects covering the handle position when in use.
The following is the "antenna position indication image" and "signal strength and position

relationship diagram":

90°

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды