Wfly ET08 страница 58 Скачать руководство пользователя

Страница: 58 / 84

THROTTLE CURVE

Interface path: HOME/MON. → [MODEL MENU] → [THROTTLE CURVE]

EXP+7 point broken line, adjust the throttle output curve according to the throttle stick action, so that the

engine (motor) revolution reaches the optimal ﬂight state.

Standard Curve

Idle Curve 1

Idle Curve 2

Curve setting example

The following curves are made in the default polyline adjustment. When the curve is actually set, it is

input according to the speciﬁed (or reference value) action amount of the model.

- Adjustment of the stunt curve: The stunt curve is used to keep the engine at a certain speed even if the

pitch is reduced during high altitude ﬂight. For the purpose of movements such as tendons, roll, and 3D,
special eﬀects curves are sometimes used depending on the stunt action.

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition]. Switching by

the switch, the function curve setting is performed separately.

- Adjustment of the standard curve: The standard curve is a basic curve set with hovering as the center.

With the pitch curve (standard), the number of engine revolutions is ﬁxed, and the up and down control is
the easiest.

EXP fuses 7-point polyline mode.

Adjust the upper and lower oﬀset of the selected curve reference

point, and switch the reference point by conﬁrming key (long press

to reset value).

Adjust the rate of output value of left and right curves respectively

Fly mode" controls the pitch curve, and diﬀerent modes

are enabled for curve adjustment when setting.

MODEL MENU \ HELICOPTER

WARNING

When starting the engine, be

sure to start the engine at normal

idle speed in normal mode.

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды