Wfly ET08 страница 62 Скачать руководство пользователя

Страница: 62 / 84

GYRO

This function is used to adjust the gyroscope sensitivity. Set the sensitivity and mode of operation

(normal/AVCS) for each ﬂight condition or switch.

Interface path: HOME/MON. → [MODEL MENU] → [GYRO]

The control gyro sensitivity can be activated by "Fly

Condition" or by assigning switches, knobs, and so on.

3 modes can set the sensitivity separately

A switch, knob, etc. can be set to activate the sensitivity

value of the speciﬁed position of the switch.

Normal mode, (AVCS) locktail mode.

Set the associated tuning control switch, knob, etc. for

sensitivity adjustment

Gyro operation mode. Normal, AVCS100%

Can set the trim range value ±20%

Control switch current real-time position

Disable and enable the current Gyro conﬁguration group.

Each control switch may be provided gyro respectively,

three kinds of sensitivity can be provided.

5 Type selecting. Select the sensitivity type of the corresponding work for the current "position".

The sensitivity required for diﬀerent ﬂight modes is diﬀerent, so switch the conditions (Position)

separately for sensitivity adjustment.

7 Trim the switch selection and trim the ratio setting. Sensitivity tuning switch, the default is [--]; the rate

value can be set to ±20%. Used for trimming the sensitivity.

1 When using the function, ﬁrst assign the function channel on the [Function] interface, and set the

"Switch” and “Trim” to [--] in [Function].

Function setting

4 Status selecting. Select whether the "Position" conﬁguration above is enabled or not.

2 Mode selecting. Optional "switch" or "Fly condition".
3 Position selecting. In each mode, there are 3 groups of positions to choose from, and the

corresponding sensitivity can be set separately. In the "switch" mode, you need to select the position
switch, the default is [--].

6 Ratio adjustment. The options vary depending on the type option ("Normal" type, "Rate" range 0%-

100%; under "AVCS" type, "Rate" range is Normal[0~100%], AVCS[0~100%]) .

MODEL MENU \ HELICOPTER

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды