manualshive.com logo in svg

Wfly ET08, Инструкция по эксплуатации

Поделиться
Скачать
Wfly ET08 Скачать руководство пользователя страница 63

GOVERNOR

This function is used to switch the speed of the helicopter rotor head. The helicopter head speed can be 

switched by a hardware switch for each flight condition.

Interface path: HOME/MON. → [MODEL MENU] → [GOVERNOR]

The control governor can be activated by "Fly Condition" 

or by assigning switches, knobs, etc.

The 3 "Fly Mode"can be set governor seperately

Can customize the switch, knob, etc. to control the 

designated position of the activation switch.

Set up the relevant tuning control switch, knob, etc.

Speed adjustment. Ordinary, 100%

Tuning set range value ±20%.

Real-time numerical

Disable and enable the current "Governor" configuration 

group.

Each control switch can be set separately for the 

governor, and  3 positions can be set.

1 When using the function, firstly assign the function channel on the [Function] interface, and set the 

“Switch” and “tuning” to [--] in [Function].

5 Ratio adjustment. Change the ratio and adjust the speed.

Function

3 Location selection. In each mode, there are 3 groups of positions to choose from, and the speed (rate) 

under the models can be set separately. In the switch mode, you need to select the position switch, the 
default is [--].

4 Status selection. Select whether the "Position" configuration above is enabled or not.

2 Mode selection. Optional "switch" or "Flight Condition" mode.

6 Tuning the switch selection and trimming the rate setting. Sensitivity tuning switch, the default is [--]; 

the rate value can be set to ±20%. Used to tuning the speed. (When the tuning switch is [--], the preset 
tuning ratio speed correction is performed by default.)

63

MODEL MENU \ HELICOPTER

C

o

n

d

it

io

n

m

o

d

e

S

w

it

c

h

m

o

d

e

Содержание ET08





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды