Wfly ET08 страница 74 Скачать руководство пользователя

Страница: 74 / 84

ELEVATOR

Adjust the amount of movement of the elevator separately

Adjust the amount of action of the aileron action on the

elevator. (Set to 0 if only the 2 servos of the elevator are used
instead of the ailerons)

If the aileron type is selected in the model type selection function of the context menu and the aileron

type is selected in the tail type, the elevator of the aileron elevator tail type can be adjusted in this setting
interface. (Only for the body with one servo on each side of the elevator)

Interface path: HOME/MON.→ [MODEL MENU] → [ELEVATOR]

When operating the ailerons, let the elevator servo act as aileron to improve the performance of the

rolling shaft.

Range±120%,default 100%

● The amount of operation of each servo can be adjusted separately. (For the connection method of the

servo, please refer to "Servo connection of diﬀerent model categories")

● When the connection causes the mixing direction to be reversed, it can be adjusted by changing the

polarity (+/-) of the action amount.

● If the amount of motion is too large or the rudder is repeatedly played, the servo may be unresponsive.

Be sure to conﬁrm the actual movement of the body when setting.

Elevator

Elevator2

MODEL MENU \ AIRPLANE

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды