Wfly ET08 страница 64 Скачать руководство пользователя

Страница: 64 / 84

SWASH

Interface path: HOME/MON. → [MODEL MENU] → [SWASH]

Connecting rod correction function of swash (except for H-1 mode of swash)

Swash travel: function to adjust the movement of aileron, elevator, and pitch.(can be

reduced/increased/reversed)

Range ±100%, Default 50%

Range ±100%, Default

50%

1 Move the cursor to the "midpoint position" and click to get (no key setting is supported) to read the

position of the throttle rocker (the neutral point value of the steering gear).After reading the neutral point
value, use other correction functions for subsequent Settings.

Steps for setting mixed control rate

* Take HR3 as an example to describe the setting process of mixed control rate.

1 Adjust the servo rocker arm to make the neutral point in the 50% range, in order to make the mixed

control value as small as possible.

Neutral point setting process

(reference point for setting correction function)

● Set the throttle stick to a preset neutral position.Adjust the length of the connecting rod so that the

cross disc remains level at this point.

● Trim function to make small adjustments.

2. Adjust the operation of elevator
Adjust the elevator rocker up and down so that the aileron or pitch direction is not disturbed.

● Adjust the ratio data to be corrected

Adjust the aileron stick to move left and right so that the collective or pitch direction does not interfere.

● Adjust the pitch curve in a straight line and make the helicopter pitch reach the maximum value.

* Adjust the ratio so that when the throttle lever is idle and full, make sure the swash is only moving

horizontally.

1. Adjust the aileron operation

MODEL MENU \ HELICOPTER

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды