Wfly ET08 страница 55 Скачать руководство пользователя

Страница: 55 / 84

FLIGHT MODE

For details, please refer to the instruction manual of the ﬂight control board, and set the most reasonable

operation mode according to the user's own usage habits.

Interface path: HOME/MON. → [GENERAL MENU] → [FLIGHT MODE]

This function can be combined by two arbitrary switches or knobs, rockers, etc. to form up to 9 diﬀerent

ratios of output. Each output user can set it according to actual needs, which is suitable for some ﬂight
control boards for various ﬂight conditions. Demand for use.

The arrow position is the active position of the current switch gear combination and does not aﬀect the

setting parameters.

Mode Description:

There are up to 9 mode outputs (3 positions switch x 3 positions switch = 9 states).

There are at least 4 mode outputs (2 positions switch x 2 positions switch = four states).

Function Status

Control Switch 1
Control Switch 2

The arrow indicates

where the eﬀect is

GENERAL MENU

WARNING

Please verify the setting result

after setting. Please remove the

blade when is commissioning veriﬁcation,be
careful to avoid injury by the model.

Содержание ET08





















































































Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды

Wfly ET08, Инструкция по эксплуатации

Результаты поиска

Содержание ET08

Отзывы:

Похожие инструкции для ET08

Бренды по названию

Популярные бренды