Wfly ET08 страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 84

background image

Basic Operation

Left and right stick mode replacement method

It is not recommended to replace the left and right sticks by yourself, otherwise the transmitter may be

damaged.

1 Loosen the bearing housing screws (the screws do not need to be fully retracted), then remove the

spring, bracket 7 and bracket 5 and tighten the screws; then remove the removed spring, bracket 7 and
bracket 5 in another assembly corresponding position (remove the bearing housing screw before

assembly),The tightness of the stick can be changed by adjusting the height of screw 3.

Required tools: 3 mm cross screwdriver, 1.5 mm hex driver

Firstly open the transmitter housing and then follow the instructions shown below:

2 Remove the screw of the throttle reed, the throttle reed and the throttle sleeve, and install them in the

corresponding position of the other assembly. According to your own habits, select the type of throttle
sliding (toothed and smooth) and adjust the screw (screw 1 or The height of the screw 2) makes the
damping of the throttle conform to your own habits.

Screw 2

Throttle reed

Throttle sleeve

After the throttle structure is modiﬁed, turn on the machine, enter [system setting] → [stick mode], select

the corresponding operation mode, and then adjust the stick after replacing the left and right modes! If you
need components such as bracket 5 (such as the parts needed for assembling double circuit structure!), you

can e-mail to WFLY overseas seller to order the spare parts at sales@wﬂysz.com.

Bracket 5

Bracket 7

Spring

Throttle sleeve

Screw 1

①

Screw 3

Screw 3

Bearing
housing screw

14

«
...
12
13
14
15
16
...
»

Содержание ET08





















































































Отзывы:

Нет отзывов

Похожие инструкции для ET08

wM-Bus 868 USB Key

Бренд: MADD Страницы: 4

Бренд: M-system Страницы: 18

VE.Direct LoRaWAN Series

Бренд: Victron energy Страницы: 7

Tilted Element DT800

Бренд: Airmar Страницы: 4

Бренд: F&F Страницы: 2

Бренд: Hallicrafters Страницы: 28

Бренд: halstrup-walcher Страницы: 12

LonWorks LPT-11

Бренд: Echelon Страницы: 76

Бренд: RC4 Wireless Страницы: 14

Бренд: RTI Страницы: 4

RV-100 RealVision 3D

Бренд: Raymarine Страницы: 2

Бренд: GEARUP Страницы: 6

ATLAS 1000 AR144

Бренд: ITB Страницы: 41

Бренд: Murata Страницы: 82

CodePlus HCS7720 Series

Бренд: LG Страницы: 28

CodePlus HCS6300 Series

Бренд: LG Страницы: 52

Бренд: LG Страницы: 7

Бренд: CamRanger Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды