WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 17

Страница: 17 / 136

765-4501/0100-0000

Properties

Product manual | Version: 1.1.0

8PORT IOL-A FLD EI DC 24V 2.0A

4.2 Connections

4.2.1 Power supply

The product is powered through the X31 connection (Power in). Two supply cables can
be connected to the plug:
• Supply cable 1: 1L+ (U

) and reference potential 1L−

• Supply cable 2: 2L+ (U

) and reference potential 2L−

Both supply cables are electrically isolated from each other and functional ground.

Each pin of plug X31 (Power in) is connected to the same pin of socket X32 (Power out)
and makes it possible to pass the power on to the next device.

Table 4: Supply voltage

Supply Voltage In-
put

Supply Voltage
Output

Pin

Signal

Description

1L+

24 VDC supply voltage U

for system

and sensor/actuator

2L−

Reference potential for 2L

1L−

Reference potential for 1L

2L+

24 VDC auxiliary/control voltage U

Functional ground

M12, L-coded, plug,
5-pin (4 + FE)

M12, L-coded,
socket, 5-pin (4 +
FE)

Note

Upper limit on current consumption from X32 (Power out)

Before connecting one or more products to the power supply on socket X32 (Power out),
read section

Power Supply Examples [

}

61]

. There you will find information on the

maximum permitted current consumption.

4.2.2 Communication Interfaces

4.2.2.1 IO-Link (Master)

Table 5: IO-Link (class A)

IO-Link (Class A)

Pin

Signal

Description

Wire Color

M12, A-coded,
socket, 5-pin

1L+

24 VDC supply voltage U

for sensor/actu-

ator

Brown

DIO B (DI B/
DQ B)

Digital input/output channel B

White

1L–

Reference potential for 1L+

Blue

C/Q
DIO A (DI A/
DQ A)

IO-Link data or
digital input/output channel A

Black

n. c.

Not connected

Содержание TEchDocs 765-4501/0100-0000









































































































































Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды

WAGO TEchDocs 765-4501/0100-0000, Руководство пользователя

Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды