WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя | Manualshive

Страница: 8 / 136

background image

765-4501/0100-0000

Provisions

8

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

Improper Use

Improper use of the product is not permitted. The following cases in particular constitute
improper use:
• Non-observance of the intended use.
• Use without protective measures in an environment in which salt water, salt spray mist,

icing, corrosive fumes, explosive gases, direct sunlight and ionizing radiation can oc-
cur.

• Use of the product in areas with special risk that require continuous fault-free operation

and in which failure of or operation of the product can result in an imminent risk to life,
limb or health or cause serious damage to property or the environment (such as the
operation of nuclear power plants, weapons systems, aircraft and motor vehicles).

Warranty and Liability

The terms set forth in the General Business and Contract Conditions for Delivery and
Service of WAGO Kontakttechnik GmbH & Co. KG and the terms for software products
and products with integrated software stated in the WAGO Software License Contract –
both available at

ü

www.wago.com

– shall apply. In particular, the warranty is void if:

• The product is improperly used.
• The deficiency (hardware and software configurations) is due to special instructions.
• Modifications to the hardware or software have been made by the user or third parties

that are not described in this documentation and that has contributed to the fault.

Individual agreements always have priority.

Obligations of Installers/Operators

The installers and operators bear responsibility for the safety of an installation or a sys-
tem assembled with the products. The installer/operator is responsible for proper installa-
tion and safety of the system. All laws, standards, guidelines, local regulations and ac-
cepted technology standards and practices applicable at the time of installation, and the
instructions in the the products’ Instructions for Use, must be complied with. In addition,
the Installation regulations specified by Approvals must be observed. In the event of non-
compliance, the products may not be operated within the scope of the approval.

«
...
6
7
8
9
10
...
»

Содержание TEchDocs 765-4501/0100-0000









































































































































Отзывы:

Нет отзывов

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренд: Harrington Страницы: 8

Бренд: GE Страницы: 36

Бренд: Handicare Страницы: 32

Бренд: IFM Страницы: 13

Бренд: CAME BPT Страницы: 8

Бренд: Balboa Water Group Страницы: 88

Бренд: Monacor Страницы: 14

IP Solutions VIP-172L

Бренд: Valcom Страницы: 4

Бренд: NA-DE Страницы: 18

Бренд: Crosby Страницы: 8

R7F4DC-DAC16D-H

Бренд: M-system Страницы: 8

Бренд: Avidsen Страницы: 180

Бренд: Balluff Страницы: 4

Бренд: Real Time Devices Страницы: 45

Бренд: i4Technology Страницы: 6

HydroTap G4 802701

Бренд: Zip Страницы: 24

Бренд: Kongsberg Страницы: 34

BACnet iSMA-B-MINI

Бренд: iSMA CONTROLLI Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды