WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 126

Страница: 126 / 136

765-4501/0100-0000

Service

126

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

Service

12.1 Resetting to Factory Settings

The device can be reset to the factory settings. Use the WAGO I/O Field Webserver for
this purpose.

You can find information on the procedure under Parameterizing the Module via the
WAGO I/O Field Webserver >

Resetsetting the Module to the Factory Settings

[

}

102]

12.2 Updating Firmware

The device’s firmware can be updated. Use the WAGO I/O Field Webserver for this pur-
pose.

You need the firmware file corresponding to the module type. The name of the firmware
file is always

FWUPDATE.zip

; you can store it in a folder with the name of the module

(e.g., 0765-4501).

You can find information on performing firmware updates under Parameterizing the Mod-
ule via the WAGO I/O Field Webserver >

Updating Firmware [

}

100]

Содержание TEchDocs 765-4501/0100-0000









































































































































Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды

WAGO TEchDocs 765-4501/0100-0000, Руководство пользователя

Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды