WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 136

background image

765-4501/0100-0000

Commissioning

94

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

Selection Option

Explanation

Digital input, normally
closed

Pin 2 is a digital input. The signal is inverted.

Digital Output

Pin 2 is a digital output.

Digital output, static on

Pin 2 is a digital output. The signal is permanently set to logic 1 (for testing pur-
poses only).

Configuring the Device Check for Validation and Backup

Note

In the “IOL Autostart” operating mode (see above), this drop-down menu has no ef-
fect.

The

Validation and backup

drop-down menu can be used to determine whether a vali-

dation (device check) is performed and, if so, at what level (Inspection Level) when a con-
nected device is replaced, and whether or not the stored operating parameters of the old
device are carried over to the new one.

The following table explains the possible values for Inspection Level:

Table 61: Possible Values of the

Inspection Level

Parameter

Inspection Level

Description

NO_CHECK

No device check is performed.

TYPE_COMP

A device check for type compatibility is performed.

For the device check, the actual vendor ID is compared to the vendor ID setting in
the configuration, and the actual device ID is compared to the device ID setting in
the configuration.

IDENTICAL

A device check for device identity is performed.

For this purpose, a device check for type compatibility is performed. Furthermore,
the actual serial number is compared to the serial number setting of the configura-
tion.

The

Backup Level

parameter determines the system behavior when a device connected

to the port is replaced in terms of continued operation with unmodified device parameters.

This parameter can have three different values:

Table 62: Possible Values of the

Backup Level

Parameter

Backup Level

Description

Commissioning
(“Disable”)

Parameter data of the old device is not saved for transfer to the new device. There-
fore, if the device is replaced, the new device must be parameterized anew.

Production
(“Backup/Restore”)

Changes to all active parameters within the device are copied and saved. Thus all
parameter data of the old device is stored for transfer to a new device.
Device replacement with automatic or semi-automatic data storage is supported.

Production
(“Restore”)

Changes to all active parameters within the device are not copied and saved. Only
special parameter data of the old device is stored for transfer to a new device.
Device replacement with automatic or semi-automatic data storage is only sup-
ported for these “frozen” parameters.

The

Validation and Backup

drop-down menu offers the following options for setting the

Inspection Level

and

Backup Level

parameters:

«
...
92
93
94
95
96
...
»

Содержание TEchDocs 765-4501/0100-0000









































































































































Отзывы:

Нет отзывов

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренд: LAON TECHNOLOGY Страницы: 2

Бренд: La Gard Страницы: 2

Spray Away 5266

Бренд: Havahart Страницы: 6

CPX-AP-I-8DI-M8-3P

Бренд: Festo Страницы: 18

Бренд: Sandstrom Страницы: 32

Бренд: Vimar Страницы: 16

Бренд: Watts Страницы: 24

Бренд: b-red Страницы: 28

Бренд: Viking Страницы: 11

K-1200-IP Series

Бренд: Viking Страницы: 25

Бренд: KOCOM Страницы: 2

Бренд: Roule Страницы: 6

Бренд: Toro Страницы: 28

Бренд: WinSystems Страницы: 30

Prestige Close Coupled Systems

Бренд: Rinnai Страницы: 48

Бренд: BACKSAFE Страницы: 27

Бренд: Toa Страницы: 2

VISTADOOR VDV Series

Бренд: M-E Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды