WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя

Страница: 102 / 136

765-4501/0100-0000

Commissioning

102

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

5. Click the

[Upgrade]

button.

The firmware update is performed. After that, the port must be configured anew.

The firmware update procedure is as follows:

1. The firmware from the

FWUPDATE.ZIP

firmware container file is stored in the mod-

ule’s flash memory.

2. An internal reset is triggered.

3. Then the device maintenance firmware starts; this edits the firmware container file

and installs the new firmware, including the module’s configuration files.

4. You are notified when the installation procedure finishes.

5. The module then resets again.

6. The new firmware that has just been loaded starts.

10.3.1.4.6 Resetsetting the Module to the Factory Settings

In many cases, it can be helpful to reset the module to the factory settings. This can be
done for various selectable classes of settings with the

Settings

menu item on the

Fac-

tory reset

tab.

Figure 22:

Settings

Menu Item,

Factory Reset

Tab

Changes to settings require operator or admin rights. If you do not have these, the

Set-

tings

tab is grayed out and cannot be edited.

Various settings can be reset according to the radio button selection:

Table 67: Options for Resetting the Module to the Factory Settings

Option

Reset Settings

Reset Device Informa-
tion

Module settings (e.g., maintenance information, system time settings)

Reset Network Adapter
Settings

Network adapter settings (communication settings, IP address configuration, sta-
tion name)

Reset Application Pa-
rameters

Application-specific data (port configuration and parameters, remanent parame-
ters)

Reset All

All Settings

Содержание TEchDocs 765-4501/0100-0000









































































































































Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды

WAGO TEchDocs 765-4501/0100-0000, Руководство пользователя

Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды