WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 92

Страница: 92 / 136

765-4501/0100-0000

Commissioning

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

10.3.1.4.1 Configure Ports

Figure 16:

Port XX

Menu Item,

Configuration

Tab

The

Configuration

tab is used to display and modify the following port settings for the se-

lected port of the device:

Table 58: Port Configuration Settings for IO-Link Devices

Name

Type

Description

Port mode (pin 4)

Drop-down menu

Port operating mode (configuration of pin 4)

Digital input signal filter
(pin 4)

Drop-down menu

Filter time for digital input signals on pin 4 (only for
“Port mode (pin 4)” on digital input)

IQ behavior (pin 2)

Drop-down menu

IQ behavior of the port (configuration of pin 2)

Validation and backup

Drop-down menu

Validation and Backup Settings for Device Check
When Replacing Devices

PortCycleTime

Input field

Expected cycle time of the port

VendorID

Input field

Expected manufacturer ID of the connected device

DeviceID

Input field

Expected device ID of the connected device

The

Validation and Backup

PortCycleTime

VendorID

and

DeviceID

settings only ap-

pear for the IOL Manual selection in the

Port mode (pin 4)

drop-down menu.

Changes to settings require operator or admin rights. If you do not have these, the

Con-

figuration

tab is grayed out, and the displayed values cannot be edited.

If cyclic data exchange takes place via PROFINET, no configuration is possible. In this
case, a message appears:

Note: Changing configuration not allowed because interface state

is “communicating.”

To makes changes to a port’s configuration, proceed as follows:

1. Select the desired port (port X01, port X02 etc.) from the menu

2. Open the

Configuration

tab.

3. Configure pin 4 by setting the port operating mode.

Содержание TEchDocs 765-4501/0100-0000









































































































































Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды

WAGO TEchDocs 765-4501/0100-0000, Руководство пользователя

Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды