WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 136

background image

765-4501/0100-0000

Commissioning

Product manual | Version: 1.1.0

93

8PORT IOL-A FLD EI DC 24V 2.0A

4. If applicable, configure the filter time for the signals of the digital inputs.

5. If applicable, configure the device check for validation and backup.

6. If applicable, configure pin 2 by setting the I/Q behavior.

7. If applicable, enter the expected vendor ID.

8. If applicable, enter the expected device ID.

9. If applicable, set the expected cycle time.

10. Click the

[Apply]

button.

ð

Your changes now take effect.

Configuring the Operating Mode for Pin 4 of the Port

You can select the port operating mode for pin 4 of the selected IO-Link port from the

Port mode

drop-down list. The following operating modes are available:

Table 59: “Port Mode” Drop-Down Menu: Selecting the Operating Mode for Pin 4 of the Selected IO-Link Port

Selection Option

Description

Deactivated

The port is disabled. L+ is switched off. The process data (both input and output) is
set to 0. The master no longer performs actions related to this port.

IOL Manual

The port is used as an IO-Link port with manual (user-defined) configuration. The
vendor ID, device ID and version ID are validated.

IOL Autostart

The port is used as an IO-Link port with automatic start. No configuration or device
validation occurs.

Digital input, normally
open

The port is used as a digital input. All elements of the port configuration are ig-
nored except for the input and output data length.

Digital input, normally
closed

The port is used as a digital input. The signals to the port are inverted. All elements
of the port configuration are ignored except for the input and output data length.

Digital Output

The port is used as a digital output. All elements of the port configuration are ig-
nored except for the input and output data length.

Digital output, static on

The port is used as a digital output. The signal on pin 4 is permanently set to
logic 1 (for testing purposes only).

Setting the Filter Time for Digital Inputs

The filter time for the digital inputs can be selected from the

Digital input signal filter

drop-down menu. You can select from the following values:
• No digital input filter
• 3 ms
• 15 ms
• 20 ms

If the

No digital input filter

option is selected, no filtering occurs.

Configure Pin 2 (I/Q)

The behavior of pin 2 (I/Q) can be selected from the

IQ behavior

drop-down menu. For

your IO-Link class A device, the following configuration options are available for using
pin 2 as a digital input or output:

Table 60:

IQ Behavior

Drop-Down Menu – Configuration of Pin 2 (I/Q) for IO-Link Class A Devices

Selection Option

Explanation

Not supported

Pin 2 is not used.

Digital input, normally
open

Pin 2 is a digital input.

«
...
91
92
93
94
95
...
»

Содержание TEchDocs 765-4501/0100-0000









































































































































Отзывы:

Нет отзывов

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренд: Gainwise Страницы: 13

Бренд: iDance Страницы: 10

Бренд: GREER Company Страницы: 35

Бренд: V-Tec Страницы: 15

Бренд: Mopedia Страницы: 36

EAGLE GRIP EG4MDC2-F

Бренд: Easy Lift Equipment Страницы: 17

Бренд: Medion Страницы: 308

Бренд: Magnavox Страницы: 24

Бренд: Daewoo Страницы: 35

Бренд: 2N Страницы: 132

Бренд: Autotrol Страницы: 8

Бренд: Guardian Audio Страницы: 4

Бренд: Presto Lifts Страницы: 18

Бренд: Reliable Страницы: 2

ProcessLogix 1757-SRM

Бренд: Allen-Bradley Страницы: 36

Бренд: Fancom Страницы: 51

Бренд: LIFTINGITALIA Страницы: 24

MICROPUMP 668-400-2

Бренд: Idex Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды