WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 136

background image

765-4501/0100-0000

Provisions

Product manual | Version: 1.1.0

7

8PORT IOL-A FLD EI DC 24V 2.0A

1

Provisions

This documentation applies to the following product:

Table 1: Scope of Applicability

Item no.

Item description, long

Item description, short

0765-4501/0100-0000

8-Port IO-Link Master Class A; EtherNet/IP;
24 V DC; 2.0 A; 8 × M12 connection

8 PORT IOL-A FLD EI 24 VDC 2.0 A

1.1 Document Portfolio

Note

Observe the applicable documentation!

This product must only be installed and operated according to the instructions of the com-
plete Instructions for use. Knowledge of the complete Instructions for use is required for
proper use.

1. Carefully read the Product Manual.

2. Before commissioning, follow the instructions in section

8

.

Table 2: Complete instructions for use

Document Type

Contents

&

Product Manual

Contains all the product-specific information for a product.

&

Data Sheet

Contains the technical data and approvals / certificates for a product.

&

Instruction leaflet

Is included with each product. Contains initial information on safe handling of
the product.

All documentation is available at:

ü

www.wago.com

/<item number>.

Besides this documentation, the following supplementary document is available:
•

&

Product Manual

WAGO IO-Link Configurator

1.2 Intended Use

The product 0765-4501/0100-0000 is used to capture field signals on sensors, actuators
and hubs which have been sent or received by a higher-level controller and output them
via IO-Link.

The product works as a decentralized input/output unit in EtherNet/IP und ETHERNET
TCP/IP networks.
• This product is intended for installation in automation technology systems.
• The product meets the IP67 protection type requirements.
• The product is intended for indoor and outdoor use.
• Operation of the products in Industrial area is permitted.
• Operation of the product in other application areas is only permitted when correspond-

ing approvals and labeling are present.

«
...
5
6
7
8
9
...
»

Содержание TEchDocs 765-4501/0100-0000









































































































































Отзывы:

Нет отзывов

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 16

Бренд: Feig Electronic Страницы: 153

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: Hama Страницы: 75

Бренд: LEGRAND Страницы: 3

Бренд: Aiphone Страницы: 32

Бренд: Aiphone Страницы: 4

Бренд: Keurig Страницы: 2

Бренд: R. Beck Maschinenbau Страницы: 36

Бренд: ZKTeco Страницы: 56

MM2040 TOUCHBOX

Бренд: Manta Страницы: 16

Бренд: DSC Страницы: 4

DIY Colour Video Doorphone SW244-CVD

Бренд: Swann Страницы: 2

Бренд: Stahl Страницы: 24

L.O.C.PRO LPGL-2

Бренд: PAC Страницы: 2

Бренд: CENTRAL Страницы: 4

Бренд: 3M Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды