WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя | Manualshive

Страница: 72 / 136

background image

765-4501/0100-0000

Connection

72

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

• 1L to power the logic and sensors/actuators
• 2L to power actuators (separate actuator supply)

All supply voltages are connected via L-coded M12 pluggable connectors.

!

NOTICE

Damage to electronics

Connect each of the supply voltages (each to +24 V and 0 V) completely. Connecting
multiple supply voltages through one 0 V connection is not permitted, since this would ex-
ceed the current load capacity of the contacts.

Power Supplies 1L and 2L

The voltages 1L and 2L are electrically isolated and are fed in on connection X31.

The 1L power supply is required to power the module electronics and the connected sen-
sors/actuators. Connect it to connection X31. If you want to power additional products
through this current path, connect the cable for the additional power supply to connection
X32.

The following procedure is especially advantageous:
• Install the power supply for the module electronics independently of the power supply

for the actuators

• Provide independent fuse protection for the power supplies

This allows the network to continue to run even when peripheral parts are switched off.

!

NOTICE

Damage to electronics

The current load capacity of the L-coded M12 pluggable connector is 16 A per current
path (1L or 2L). This value must not be exceeded. To limit the sum of current paths 1L
and 2L even in the event of short circuit, it may be necessary to provide fuse protection
for them. For the calculation of the maximum permissible current feedthrough, see sec-
tion

8

Power Supply Examples [

.

Note that the connection for the additional supply voltage is not monitored for overload. If
the maximum current carrying capacity is exceeded, this can damage the pluggable con-
nectors.

WAGO recommends using pre-assembled cables.

The following figure gives an example of feeding in and passing on the supply voltages:

«
...
70
71
72
73
74
...
»

Содержание TEchDocs 765-4501/0100-0000









































































































































Отзывы:

Нет отзывов

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренд: Spon Страницы: 9

Бренд: V-Tec Страницы: 6

Бренд: M-system Страницы: 6

Бренд: TANDBERG Страницы: 12

BALBOA CS6000B Series

Бренд: HydroQuip Страницы: 32

Oxford MAJOR 190

Бренд: Sunrise Medical Страницы: 48

Бренд: Gardeners Страницы: 2

Бренд: Detection Systems Страницы: 2

Novus NVE-EP200

Бренд: AAT Страницы: 40

RaptorX-SL1200-S15

Бренд: CNC-Step Страницы: 102

Бренд: dB Technologies Страницы: 32

Бренд: WALTCO Страницы: 48

Бренд: Bürkert Страницы: 48

Бренд: Affordable Wheelchair Lifts Страницы: 74

Бренд: Valcom Страницы: 3

Бренд: Supersonic Страницы: 6

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды