WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 136

background image

765-4501/0100-0000

Diagnostics

Product manual | Version: 1.1.0

119

8PORT IOL-A FLD EI DC 24V 2.0A

LED

Color

State

Description

identity object 1 of the adapter. The MS
LED and NS LED go through the flashing
sequence simultaneously.

Red

Flashing (1 Hz)

Connection timeout:

An IP address is con-

figured, and, for an Exclusive Owner con-
nection for which this module is the destina-
tion, the time limit has been exceeded. The
NS LED is not permanently reset to green
until all Exclusive Owner connections
whose time limits were exceeded are
reestablished.

Red

On

Duplicate IP:

The module has detected

that its IP address is already being used.

Off

Off

Switched off, no IP address:

The module

has no IP address or is switched off.

Table 83: EtherNet/IP Module LED States

LED State

Definition

Flashing
(1 Hz)

The LED switches on and off in phases at a frequency of about 1 Hz:
on for 500 ms and then off for 500 ms.

Rapid flashing
green/red/green

The MS LED or NS LED lights up green for 250 ms, then red for 250 ms, then green
again (until the test is completed).

Flashing sequence
red/green/off

The MS LED and NS LED both light up red for 500 ms, then light up green for 500 ms,
then go out for 500 ms. The flashing sequence repeats at least six times.

Table 84: Ethernet Status

LED

Color

State

Description

LNK

(Link)

LED green

Green

On

The module is connected to the Ethernet.

Off

Off

The module is not connected to the Ether-
net.

ACT

(Activity)

LED yellow

Yellow

Flickering (load-de-
pendent)

The module is sending/receiving Ethernet
frames.

Off

Off

The module is not sending/receiving Ether-
net frames.

Table 85: LED States – Ethernet

LED State

Definition

Flickering
(load-dependent)

The LED indicates high ETHERNET activity by switching on and off at a frequency of
10 Hz:
“On” for 50 ms and then “Off” for 50 ms.
The LED indicates low ETHERNET activity by switching on and off at irregular intervals.

Bluetooth Status

The Bluetooth

®

LED is integrated into the Bluetooth

®

antenna and indicates the connec-

tion status.

Table 86: LED States

®

LED

Color

State

Description

BT

Duo LED, blue/red

Blue

On

Bluetooth

®

connection established

Off

Off

Bluetooth

®

inactive

«
...
117
118
119
120
121
...
»

Содержание TEchDocs 765-4501/0100-0000









































































































































Отзывы:

Нет отзывов

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренд: 2easy Страницы: 12

Бренд: 2easy Страницы: 30

WIZARD ELEGANCE IP

Бренд: Fasttel Страницы: 14

GreenSpec HTHB-HVRGRN

Бренд: Halsey Taylor Страницы: 7

Бренд: Omniflex Страницы: 2

Бренд: ShoreStation Страницы: 19

Бренд: Gage Страницы: 36

Бренд: AXEM Technology Страницы: 31

Бренд: Feig Electronic Страницы: 35

Бренд: Elvox Страницы: 36

Бренд: Xantech Страницы: 4

Бренд: BEG Страницы: 216

ShoreStation SSPV30120MS

Бренд: Midwest Industries Страницы: 17

Бренд: Bang & Olufsen Страницы: 44

Torsion Add-on Version 3

Бренд: Instron Страницы: 32

Бренд: Sygonix Страницы: 120

Бренд: Redback Страницы: 16

Бренд: Chamberlain Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды