WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 136

background image

765-4501/0100-0000

Safety

12

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

2

Safety

This section contains safety rules that must be followed for hazard-free use of the prod-
uct.

This section is aimed at the following target groups:
• Planners and installers
• Operators
• Qualified assembly personnel
• Qualified installation personnel (electrical installation, technician network installation

etc.)

• Qualified operating personnel
• Qualified service and maintenance personnel

Obey the following safety rules:

2.1 General Safety Rules

• This documentation is part of the product. Therefore, retain the documentation during

the entire service life of the product. Pass on the documentation to any subsequent
user of the product. In addition, ensure that any supplement to this documentation is
included, if necessary.

• The product must only be installed and put into operation by qualified electrical special-

ists per EN 50110‑1/-2 and IEC 60364.

• Comply with the laws, standards, guidelines, local regulations and accepted technol-

ogy standards and practices applicable at the time of installation.

2.2 Electrical Safety

Power Supply

• Only operate the product with safe extra low voltage power sources (PELV or SELV).
• Connecting impermissible current or frequency values may destroy the product.

Grounding/Protection/Fuses

• Connect the product and system to functional ground (FE).
• When handling the product, please ensure that environmental factors (personnel, work

space and packaging) are properly equalized. Do not touch any conducting parts.

Cables

• Maintain spacing between control, signal and data lines and the power supply lines.
• Only use conductor cross-sections sufficient for the current load.

Protection

• When working on the system (e.g., during maintenance), protect the Facility part in

question from accidental or unauthorized restart.

Shielding/Network

• Observe the applicable standards for EMC-compatible installations.

«
...
10
11
12
13
14
...
»

Содержание TEchDocs 765-4501/0100-0000









































































































































Отзывы:

Нет отзывов

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренд: Rain Bird Страницы: 9

Бренд: Gardigo Страницы: 24

Бренд: Safeline Страницы: 28

Бренд: Safeline Страницы: 8

Бренд: V-Tec Страницы: 4

NuDAQ cPCI-7248

Бренд: ADLINK Technology Страницы: 59

Бренд: ENTRYPASS Страницы: 42

Бренд: EAE Страницы: 50

CONPROSYS CPS-MC341-DS1-111

Бренд: Contec Страницы: 71

Бренд: Solar Energy Страницы: 4

TrueAlert ES Series

Бренд: Simplex Страницы: 4

Бренд: Aiwa Страницы: 46

Бренд: Bluestream Страницы: 4

Бренд: Lincoln Electric Страницы: 23

Бренд: Jet Страницы: 16

Бренд: HIKVISION Страницы: 66

Бренд: Poweramp Страницы: 40

ePowerSwitch 8 Master

Бренд: Neol Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды