WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 104

Страница: 104 / 136

765-4501/0100-0000

Commissioning

104

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

Displaying Information on the Product’s Bluetooth

Interface Module

The

Information

section of the

Bluetooth

tab shows the following information on the

product’s Bluetooth

interface module:

• Current version of the Bluetooth

firmware used

• Current version of the Bluetooth

hardware used

• Chip identifier of the Bluetooth

chip used

• Interface identifier of Bluetooth

interface module

• Individual DM code of the product

(can be scanned by a smartphone or tablet to launch an app on it for communication
with the product)

Displaying Diagnostic Information

The

Diagnostics

section of the

Bluetooth

tab shows the following diagnostic information

on the Bluetooth

connection:

• Connected Status
• Connection counter; is set to 0 with each new Bluetooth

connection.

• Number of bytes sent over the Bluetooth

connection

• Number of bytes received over the Bluetooth

connection

• Last error code that occurred during operation of the Bluetooth

connection

• Status of the last Bluetooth

firmware update

• Result of the last Bluetooth

firmware update

The status of the last Bluetooth

firmware update is indicated as follows:

Table 68: Status of the last Bluetooth

firmware update

Value

Status

Ready for operation

Firmware file is being checked

Firmware update is being performed

Activating the Bluetooth

Interface Using the DM Code Displayed

Note

Never use the product in areas where operation of radio equipment is prohibited.

The product contains a radio transmitter that can impair the function of electronic medical
devices such as hearing aids and pacemakers.

Note

Only use the product with Bluetooth

if the product has an approval for the specific

country or region.

To enable the Bluetooth

interface, you must have the WAGO I/O Field app installed on

the smartphone or tablet. Proceed as follows:

•

A DM code appears in the “Information” section of the

Bluetooth

tab. Scan it with

the smartphone or tablet.

The smartphone or tablet then sends an optical sequence (flash code) to the de-
vice’s integrated light sensor.

Содержание TEchDocs 765-4501/0100-0000









































































































































Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды

WAGO TEchDocs 765-4501/0100-0000, Руководство пользователя

Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды