WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 96

Страница: 96 / 136

765-4501/0100-0000

Commissioning

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

1. Select the port to which the IO-Link device is connected from the menu on the left.

2. Open the

IOL

tab.

The

IOL

tab appears.

Read Access

Figure 17: Ports X01 ... X08 – Read Access to IO-Link Device

To read data from the connected IO-Link device, proceed as follows:

1. On the

IOL

tab, enter the index of the connected IO-Link device you want to access

into the

Index

field as a hexadecimal value.

2. On the

IOL

tab, enter the subindex of the connected IO-Link device you want to ac-

cess into the

Subindex

field as a hexadecimal value; the default setting is 00

3. Click the

[Read]

button.

The read operation is performed. An entry is written to the history at the bottom of the
tab and logged there with the current time.

If the operation was successful, the text

Read ok:

and the result appear in the history.

The entries in the history then have the following structure:

Time – Index:Subindex – Read ok: <Result>

Содержание TEchDocs 765-4501/0100-0000









































































































































Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды

WAGO TEchDocs 765-4501/0100-0000, Руководство пользователя

Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды