WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 70

Страница: 70 / 136

765-4501/0100-0000

Installation and Removal

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

• Grounding can be done separately via a cable lug and the mounting hole if the module

is installed on a non-conductive subsurface

Ensure proper contacts and a sufficient cable cross-section.

8.2 Removal

8.2.1 Tools Required for Removal

For removal, you need an Allen key to unscrew the M4 cylinder head hex screws per
DIN 912/ISO 4762.

8.2.2 Before Removal

CAUTION

Device gets hot

During operation, high surface temperatures can arise on the metal housing and metal
connection sockets. If the product has been in operation, allow it to cool before touching
it, or use gloves.

Prepare for removal as follows:

1. If the product is contaminated, clean it before removal. It is especially important to

clean contaminated screw-clamp connections.

2. Before removal, loosen all screw connections on the connectors and disconnect the

cables.

3. Ensure that the equipment part on which you mounted the product is de-energized.

4. Unscrew the two M4 cylinder head screws and remove the product.

8.2.3 Removal

To remove the product, e.g., when replacing a device, proceed as follows:

1. Ensure that the equipment part on which you mounted the module is de-energized.

2. Unscrew the two M4 cylinder head screws with the Allen key.

3. Remove the product.

8.2.4 After Removal

If the product that has been removed is defective, mark it as defective to prevent reuse of
the product.

Содержание TEchDocs 765-4501/0100-0000









































































































































Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды

WAGO TEchDocs 765-4501/0100-0000, Руководство пользователя

Результаты поиска

Содержание TEchDocs 765-4501/0100-0000

Отзывы:

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренды по названию

Популярные бренды