WAGO TEchDocs 765-4501/0100-0000 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 136

background image

765-4501/0100-0000

Safety

Product manual | Version: 1.1.0

13

8PORT IOL-A FLD EI DC 24V 2.0A

2.3 Mechanical Safety

• Cooling of the product must not be impaired. Ensure air can flow freely and that the

minimum clearances from adjacent products/areas are maintained.

• Do not install the product on or in the vicinity of easily flammable materials.
• Before startup, please check the product for any damage that may have occurred dur-

ing shipping. Do not put the product into operation in the event of mechanical damage.

2.4 Thermal Safety

• The surface of the housing heats up during operation. Under special conditions (e.g., in

the event of a fault or increased surrounding air temperature), touching the product
may cause burns. Allow the product to cool down before touching it.

• If the surface temperature of the product can exceed 55 °C, wear protective gloves and

attach protective covers and/or touch-proof protection.

2.5 Indirect Safety

• Only use a dry or cloth or a clothed dampened with water to clean the product. Do not

use cleaning agents, e.g., abrasive cleaners, alcohols or acetone.

• Do not allow the product to come into contact with ketones (e.g., acetone) or chlori-

nated hydrocarbons (e.g., dichloromethane) under any circumstances.

• Do not use hard objects that could cause scratches for cleaning.
• Clean tools and materials are imperative for handling the product.
• If automation solutions are implemented that can cause personal injury or major prop-

erty damage in the event of failure, you must take appropriate measures to ensure that
the system remains in a safe operating state even in the event of failure.

• Before installation and operation, please read the product documentation thoroughly

and carefully. In addition, note the information on the product housing and further infor-
mation, e.g. at

ü

www.wago.com

/<item number>.

• Only permit skilled personnel approved by WAGO to perform repair work.

«
...
11
12
13
14
15
...
»

Содержание TEchDocs 765-4501/0100-0000









































































































































Отзывы:

Нет отзывов

Похожие инструкции для TEchDocs 765-4501/0100-0000

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 33

Бренд: V-Tec Страницы: 16

Бренд: JBL Страницы: 24

Бренд: HIKVISION Страницы: 30

Бренд: Rain Страницы: 2

Бренд: Valcom Страницы: 6

Бренд: Vestil Страницы: 6

Бренд: JAMO Страницы: 72

Бренд: Ravaglioli Страницы: 102

Бренд: Alcad Страницы: 28

Бренд: KOCOM Страницы: 2

Бренд: Grace Digital Страницы: 1

Бренд: APS Resource Страницы: 28

Бренд: Champion Autolift Страницы: 14

Бренд: Zazen Страницы: 8

Бренд: Balluff Страницы: 7

Бренд: Vahle Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды