ViaSat 8116 Series Скачать руководство пользователя

Страница: 169 / 188

UPPER MOUNT

CHECK

NOTE

The hub assembly process requires a large (14 feet diameter) area which is flat, clean, and capable of
handling at least 18,000 lbs (8,165 kg).

PAGE

_____

Determine center of azimuth sector.

3-1

_____ Remove

necessary bolts. Install pivot frame brace and drive pivot frame.

3-1

_____

Install rotating frame.

3-2

_____

Install stow pins.

3-2

_____

Torque rotating frame fasteners.

3-2

_____

Install azimuth drive assembly.

3-14

_____

Torque azimuth assembly fasteners.

3-15

_____

Install elevation drive assembly.

3-19

_____ Place hub segment with two elevation pivots upright (elevation pivots facing up) on one side of assembly area. Assembly area

should be flat and 4 X 4s should be used to set the hub segments onto during the hub assembly process.

3-22

_____ Place segment splice onto left side of hub segment using three bolts without washers and nuts. Bolts hold spacer plate in place

during installation of the next segment.

3-22

_____

Align and secure next hub segment to left side of first hub segment.

3-22

_____ Place segment splice onto left side of second hub segment using three bolts without washers and nuts. Bolts hold spacer plate

in place during installation of the third segment.

3-22

_____

Attach elevation jack plate onto remaining hub segment (pivot facing up) using three bolts without washers and nuts. Bolts
hold spacer plate in place during installation of the third segment.

3-22

_____

Align and secure last hub segment to other two segments.

3-22

_____

Attach two elevation angle plates on each side of hub segment with elevation jack plate.

3-23

_____

Ensure upper and outside seams are even then torque all hub assembly fasteners.

3-23

_____

Lift hub assembly and attach hub elevation pivot brackets to rotating frame pivot brackets.

3-23

_____

Attach hub elevation drive bracket to elevation drive assembly.

3-23

_____

Install ladders for access to rotating frame and hub.

3-29

_____

Install guard rails on work platform.

3-29

_____

Attach covers, standpipes, and tread plate.

3-30

A-3

Содержание 8116 Series





























































































































































































Результаты поиска

Содержание 8116 Series

Отзывы:

Похожие инструкции для 8116 Series

Бренды по названию

Популярные бренды

ViaSat 8116 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 8116 Series

Отзывы:

Похожие инструкции для 8116 Series

Бренды по названию

Популярные бренды