Veeco Dimension 3100 Скачать руководство пользователя страница 290 | Manualshive

Страница: 290 / 376

Veeco Dimension 3100 Скачать руководство пользователя страница 290

Magnetic Force Microscopy

Troubleshooting

270

Dimension 3100 Manual

Rev. D

Note:

This step is not necessary for NanoScope IV.

5. Click the

Ok

button when complete.

15.6 Troubleshooting

15.6.1 MFM Image Veriﬁcation

The procedure described above should produce a good magnetic force gradient image of the
videotape sample. If there is a problem, check that the Interleave Mode is set to Lift, that Interleave
is Enabled and that the

Scan Line

is set to Interleave. Check also that the

Interleave

values of

Drive Amplitude and Drive Frequency are initially set equal to the main

Scan Controls

values.

15.6.2 Saturation in Amplitude Detection

If using amplitude detection, the magnetic force image can saturate (appear completely featureless)
if the

Interleave

Drive Amplitude

is signiﬁcantly different than the

Drive Amplitude

in the main

scan. Adjust the

Interleave Setpoint

to restore the image.

Note:

The

Interleave Setpoint

has no physical effect in

LiftMode

since there is no

surface feedback during the lift pass.

15.6.3 Optical Interference

When using

Amplitude Detection

, optical interference may sometimes appear in the Lift

(magnetic force gradient) image when imaging highly reﬂective samples. Optical interference
appears as evenly spaced, sometimes wavy lines with ~1–2µm spacing superimposed on the lift
image. This occurs when ambient laser light (i.e., light passing around or through the cantilever,
then reﬂecting off the sample) interferes with laser light reﬂecting from the cantilever. Interference
can be alleviated by moving the beam spot up the cantilever away from the tip; one-third of the
cantilever length works well. The adjustment can be reﬁned by carefully moving the beam spot
laterally a small distance on the cantilever while scanning until interference fringes are minimized.
Be careful not to move the beam off the cantilever or feedback may be lost.

Note:

Optical interference is essentially eliminated by using phase detection or
frequency modulation.

«
...
288
289
290
291
292
...
»

Содержание Dimension 3100

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды