TANDBERG SM6610 Скачать руководство пользователя

Страница: 72 / 200

Operating the Equipment Locally – Main Menu Option 4: System Menu

Page 3-34

Reference Guide: SM6610, SM6615, SM6620 and SM6625 Satellite Modulators

ST.RE.E10152.2

Ethernet Configuration Option 6: SNMP Setup
Type 6 at the prompt to view the

SNMP Setup Menu

from the

Ethernet

Configuration Menu

. It displays the current settings and displays the

status.

TANDBERG Television SM6600 Satellite Modulator: DEV001

SNMP Setup Menu

1 Display Current Settings

2 Set SNMP to Monitoring Only

3 Set SNMP to Full Control

4 Set SNMP alarm text mode to Verbose

5 Set SNMP alarm text mode to Terse

H Help

Q Quit

Status: No Alarms

Please enter your selection, then press Enter:

Table 3.3: SNMP Setup Menu Options

Command Messages

Display Current Settings

The SNMP mode is set to Monitor Only / Full Control.
The SNMP alarm text mode is set to Verbose / Terse.

Set SNMP to Monitoring Only

SNMP mode updated.
Already set to monitor only mode.

Set SNMP to Full Control

SNMP mode updated.
Already set to full control mode.

Set SNMP alarm text mode to Verbose

SNMP verbose alarm text mode updated.
Already set to verbose alarm text mode.

Set SNMP alarm text mode to Terse

SNMP terse alarm text mode updated.
Already set to terse alarm text mode.

Содержание SM6610









































































































































































































Результаты поиска

Содержание SM6610

Отзывы:

Похожие инструкции для SM6610

Бренды по названию

Популярные бренды

TANDBERG SM6610, Справочное руководство

Результаты поиска

Содержание SM6610

Отзывы:

Похожие инструкции для SM6610

Бренды по названию

Популярные бренды