TANDBERG SM6610 Скачать руководство пользователя

Страница: 124 / 200

RS-485 Remote Control Protocol

Page 6-6

Reference Guide: SM6610, SM6615, SM6620 and SM6625 Satellite Modulators

ST.RE.E10152.2

6.2

SM66XX Remote Control

6.2.1 Outline

The SM66XX message protocol works on a configuration concept. This is

outlined in the diagram below. Instead of downloading individual

parameter values an entire configuration is handled.

Stored

Configuration

1 - 8

Current

Configuration

Download configuration to

Stored Configuation n

Message type 0x81

Retrieve Current

Configuration

Message type 0x74

Download to Current

Configuration and Activate

Message type 0x70

Retrieve Configuration

Message type 0x73

Save Current Configuration

Message type 0x80

Activate Stored

Configuration

Message type 0x71

Figure 6.1: SM66XX Remote Control

Configurations can be stored in any of the 8 slots provided or activated

immediately by downloading to the current configuration.

6.2.2 Functionality

Constraints

Certain functionality of the Modulator is dependent upon the specific

Modulator model, the hardware options fitted and the software options

installed in it. The validity of some parameter values in configuration

messages to the Modulator is dependent upon the functionality available.

Parameter values are validated by the Modulator and accepted or rejected

as appropriate. For example, 8PSK modulation and its associated FEC rate

8/9 are only available if the Higher Order Modulation (HOM) software

option is installed.

Содержание SM6610









































































































































































































Результаты поиска

Содержание SM6610

Отзывы:

Похожие инструкции для SM6610

Бренды по названию

Популярные бренды

TANDBERG SM6610, Справочное руководство

Результаты поиска

Содержание SM6610

Отзывы:

Похожие инструкции для SM6610

Бренды по названию

Популярные бренды