TANDBERG SM6610 Скачать руководство пользователя

Страница: 26 / 200

Installing the Equipment

Page 2-6

Reference Guide: SM6610, SM6615, SM6620 and SM6625 Satellite Modulators

ST.RE.E10152.2

2.3

Mains Operating Voltage, Fusing and Earthing

2.3.1 AC

Power

Supply

The Modulator operates from a wide-ranging mains power supply

(100-120 V or 220-240 Vac 50/60 Hz nominal) and is designed for use in

ambient air temperature in the range 0

C to +50

C. There are no links etc.

to be altered for operation from different supply voltages. The full

Technical Specification is given in Annex B, Technical Specification.

WARNING…

THIS EQUIPMENT SHOULD ONLY BE OPERATED FROM THE TYPE OF POWER SOURCE

INDICATED ON THE MARKING LABEL. IF YOU ARE NOT SURE OF THE TYPE TO YOUR

BUSINESS, CONSULT YOUR APPLIANCE DEALER OR LOCAL POWER COMPANY. DO NOT

OVERLOAD WALL OUTLETS AND EXTENSION CORDS AS THIS CAN RESULT IN A RISK OF FIRE

OR ELECTRIC SHOCK.

Figure 2.2: AC Power Inlet Assembly

Table 2.1: Fuse Information

Item Specification

Fuse

Single pole, fitted in live conductor in power input filter at rear of unit.

Fuse type

5 mm x 20 mm anti-surge (T) HBC, IEC/EN 60127-2 Sheet 5

Fuse rating

5 A

Fuse rated voltage

250 Vac

Power lead connector fuse (if appropriate) 5 A minimum

NOTE...
See Annex B, Technical Specification for more fuse information.

2.3.2 Technical

Earth

Figure 2.3: Location of the Technical Earth

AC Power Inlet

Fuse Carrier

To access the fuse, ease out the notch with
a small flat-blade screwdriver.

NOTE...
The Technical Earth terminal is the 6 mm tab connector.

Position of the
Technical Earth

Содержание SM6610









































































































































































































Результаты поиска

Содержание SM6610

Отзывы:

Похожие инструкции для SM6610

Бренды по названию

Популярные бренды

TANDBERG SM6610, Справочное руководство

Результаты поиска

Содержание SM6610

Отзывы:

Похожие инструкции для SM6610

Бренды по названию

Популярные бренды