TANDBERG SM6610 Скачать руководство пользователя

Страница: 143 / 200

Equipment Description

Reference Guide: SM6610, SM6615, SM6620 and SM6625 Satellite Modulators

Page 7-7

ST.RE.E10152.2

A switchable 24 V dc power supply and 10 MHz reference frequency are

combined with the L-band output for use by an external block up-converter

(BUC).

7.3.4

S11340 Host Controller Card

The microprocessor on the Host Controller Card is responsible for the

communication, configuration and monitoring functions performed by the

Modulator. It supports RS-232/485 remote control, Ethernet control,

VT100 terminal control and front panel control. Errors and alarms can be

reported via any of the aforementioned interfaces and via a simple

RESET/STATUS relay interface.
The embedded software in the Modulator also enables the user to upgrade

all of the software and firmware in the unit (via FTP) without having to

remove the chassis cover. In case of an external error in the data stream

or power supply the Modulator will always restore its last working state

when all the external errors are cleared. The embedded software controls

this recovery. For an explanation of all the control and monitoring features

refer to Chapter 3, Operating the Equipment Locally.

7.3.5

S13450 DVB ASI & SPI Input Card (Option)

Transport Stream Interface

The S13450 DVB ASI & SPI Input card can receive DVB-compliant MPEG-2

transport streams via either the Synchronous Parallel Interface (SPI) or

the two Asynchronous Serial Interfaces (ASI). The user can connect a

stream into any of the three interfaces.
It is also possible to connect two inputs; for example, it is possible to

connect a stream into both ASI Inputs. This is useful if two distinct

distribution systems are available to carry the transport stream from the

multiplex source; in case of failure on one distribution system the other

will still carry the data to be transmitted. The Modulator can be made to

switch if the input in use suffers a failure, although automatic switching is

not currently supported.
The S13450 card can accept transport streams in any of three different

data formats:

•

188-byte packets consisting of 188 contiguous data bytes

•

204-byte packets consisting of 188 data bytes and 16 RS coding bytes

(the coding bytes are ignored)

•

204-byte packets consisting of 188 data bytes and 16 dummy packets

Transport stream rate adaptation or de-jittering is performed on the

Baseband card.

Additional ASI Information

The encoded line rate of the ASI stream is 270 MBaud

100 ppm. All ASI

bytes must be 8B/10B encoded as specified by ETSI standard EN 50083-9.

Special comma characters, K28.5 code words are used as byte

synchronisation patterns. Two consecutive K28.5 code words are

transmitted prior to each MPEG-2 packet and subsequent K28.5 code

words are inserted to pad the data to achieve the required encoded ASI

line rate.

Содержание SM6610









































































































































































































Результаты поиска

Содержание SM6610

Отзывы:

Похожие инструкции для SM6610

Бренды по названию

Популярные бренды

TANDBERG SM6610, Справочное руководство

Результаты поиска

Содержание SM6610

Отзывы:

Похожие инструкции для SM6610

Бренды по названию

Популярные бренды