TANDBERG SM6610 Скачать руководство пользователя страница 56

Страница: 56 / 200

Operating the Equipment Locally – Main Menu Option 1: Quick Setup Menu

Page 3-18

Reference Guide: SM6610, SM6615, SM6620 and SM6625 Satellite Modulators

ST.RE.E10152.2

Quick Setup Menu Option 17 (SM6615, SM6625): UpConv Pwr

This is used for switching On or Off the 24 V dc power supply which may

be used to power an external block up-converter (BUC).

UpConv Pwr : Current Value= "OFF"

1 OFF

2 ON

Quick Setup Menu Option 18 (SM6615, SM6625): UpConv Ref

This is used for switching On or Off the 10 MHz frequency reference which

may be used by an external BUC.

UpConv Ref : Current Value= "OFF"

1 OFF

2 ON

Quick Setup Menu Option 17 (SM6620) / Option 19
(SM6625): =PREKOR Menu=

The

PREKOR Menu

option is available only on Modulator models SM6620

and SM6625 with the SM66XX/SWO/PREKOR software option installed. For

details of this menu option and other aspects of PREKOR™ operation, see

ST.RE.PREKOR.E10154: Reference Guide for the PREKOR Software Option

for SM6620 and SM6625 Satellite Modulators.

Quick Setup Menu Option H: Help

Type H at the prompt to view information about the options on the

Quick

Setup Menu

Quick Setup Menu Option Q: Quit

Type Q at the prompt to return to the

Main Menu

Содержание SM6610









































































































































































































Результаты поиска

Содержание SM6610

Отзывы:

Бренды по названию

Популярные бренды

TANDBERG SM6610, Справочное руководство

Результаты поиска

Содержание SM6610

Отзывы:

Бренды по названию

Популярные бренды