TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 99

Страница: 99 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

Media Board IP

Network ID
1:

The Media Processing Board is connected to the same

IP-network as the System Controller Board Interface 1.

The Media Processing Board is connected to the same IP-

network as the System Controller Board Interface 2.

Media Board IP Configuration

Media Board Configuration - Slot (1 to n)

Select Slot

to configure the Media Board(s). The pic-

ture shows that Media Boards are installed Slot 1, 2 and 3.

Indicates ok

Indicates an error

Address

The IP Address defines the network address of the Media
Board. Your LAN administrator will provide you with the cor-
rect address for this field.

Subnet Mask

The IP Subnet Mask defines the type of network. Your LAN
administrator will provide the correct value for this field.

Gateway

The IP Gateway defines the Gateway address. Your LAN ad-
ministrator will provide the correct value for this field.

Save

- Press the Save button to save changes.

Ethernet Speed
Auto:

The MCU will automatically detect the speed/duplex on

the LAN.

10Half:

The MCU will connect to the LAN using 10 Mbps/Half

Duplex.

10Full:

The MCU will connect to the LAN using 10 Mbps/Full

Duplex.

100Half:

The MCU will connect to the LAN using 100 Mbps/

Half Duplex.

100Full:

The MCU will connect to the LAN using 100 Mbps/

Full Duplex.

If forcing the TANDBERG MPS to anything other than
Auto then the Ethernet switch must also be forced to
match.

Introduction

Quick

Setup

Using

the MPS

System

Status

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Configuration

Содержание Media Processing System MPS 800




















































































































































































Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды

TANDBERG Media Processing System MPS 800, Руководство администратора

Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды