TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

TANDBERG

MPS

ADMINISTRATOR GUIDE

IP Board

IP Configuration Interface 1 and 2

As a minimum you must configure Interface 1. If your TAND-
BERG MPS is connected to two different IP-networks, you
must configure both Interface 1 and Interface 2.

INFO:

Before you can access the MPS from a web browser

the initial configuration, of a static IP address for the Sys-
tem Controller Board, is done via the LCD.

Network Configuration

Address

The IP Address defines the network address of the System
Controller Board. Your LAN administrator will provide you with
the correct address for this field.

Save

- Press the Save button to save changes.

Restart

- For the settings to take effect the unit must be restarted after pressing the Save button.

Subnet Mask

The IP Subnet Mask defines the type of network. Your LAN
administrator will provide the correct value for this field.

Gateway

The IP Gateway defines the Gateway address. Your LAN ad-
ministrator will provide the correct value for this field.

IP Interfaces Configuration

Ethernet Speed
Auto:

The MCU will automatically detect the speed/duplex on

the LAN.

10Half:

The MCU will connect to the LAN using 10 Mbps/Half

Duplex.

10Full:

The MCU will connect to the LAN using 10 Mbps/Full

Duplex.

100Half:

The MCU will connect to the LAN using 100 Mbps/

Half Duplex.

100Full:

The MCU will connect to the LAN using 100 Mbps/

Full Duplex.

If forcing the TANDBERG MPS to anything other than
Auto then the Ethernet switch must also be forced to
match.

!

97

Introduction

Quick

Setup

Using

the MPS

System

Status

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Configuration

«
...
95
96
97
98
99
...
»

Содержание Media Processing System MPS 800




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Processing System MPS 800

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: Hyundai Страницы: 26

Бренд: Fender Страницы: 6

Бренд: Jensen Marine Страницы: 18

Бренд: J&M Corporation Страницы: 9

Бренд: Rath Страницы: 7

Бренд: ICON Страницы: 6

Price Center 451

Бренд: Polycom Страницы: 4

Бренд: JETI model Страницы: 64

Бренд: Fuslon Страницы: 14

Бренд: Daewoo Страницы: 29

Бренд: RCA Страницы: 2

Бренд: RCA Страницы: 16

Бренд: BFT Страницы: 23

Бренд: Alpine Страницы: 184

Бренд: Sharp Страницы: 18

Бренд: JVC Страницы: 32

Бренд: JVC Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды