TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

TANDBERG

MPS

ADMINISTRATOR GUIDE

XML

XML Document

Configuration Using XML

XML Document

The XML Uploading page, allows administrators to upload
multiple configuration changes to the MPS instead of manu-
ally setting each entry through the web interface.

By pasting in a valid xml file, users may update the MPS
Directory and Configuration. It is also possible to execute
commands by pasting in valid command xml.

The required XML format for Directories, Configuration and
Commands can be found at the following locations:

http://<MPS IP Address>/command.xml
http://<MPS IP Address>/directory.xml
http://<MPS IP Address>/configuration.xml

If the MPS is configured for HTTPS:

https://<MPS IP Address>/command.xml
https://<MPS IP Address>/directory.xml
https://<MPS IP Address>/configuration.xml

Using the XML Document

Open the XML file, for example command.xml

1.

Copy text from the XML file

2.

Paste text into the XML Document editor field

3.

Make the desired changes

4.

Press the Save button to activate the changes

5.

Some configuration changes may require a restart of
the MPS to take effect.

Save

- Press the Save button to save changes.

Example: Text is copied from the command.xml file and pasted into the XML Document editor field.

110

Introduction

Quick

Setup

Using

the MPS

System

Status

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Configuration

«
...
108
109
110
111
112
...
»

Содержание Media Processing System MPS 800




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Processing System MPS 800

Бренд: Jensen Страницы: 12

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: WAGNER Страницы: 128

Бренд: GE Страницы: 40

Бренд: Purelogic Страницы: 60

Бренд: The Fisher Страницы: 20

Бренд: AETA Страницы: 136

Scopia XT5000 Series

Бренд: RADVision Страницы: 55

Бренд: Doppler Systems Страницы: 64

Бренд: Forge Electronics Страницы: 10

Бренд: Discount Car Stereo Страницы: 5

Бренд: Honeywell Страницы: 13

Бренд: Honeywell Страницы: 8

Бренд: Honeywell Страницы: 14

Бренд: Honeywell Страницы: 16

Бренд: Honeywell Страницы: 12

Бренд: Honeywell Страницы: 8

NOTIFIER ACS Series

Бренд: Honeywell Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды