TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 155

Страница: 155 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

SERIAL 3/4

ENET 2

ENET 1

COM 1

KB/MS

SERIAL 3/4

ENET 2

ENET 1

COM 1

KB/MS

SERIAL 3/4

ENET 2

ENET 1

COM 1

KB/MS

Inserting Additional Network Interface Cards with TANDBERG MPS 200

MPS 200 - Inserting Network Interface Cards

PRI E1/T1 ISDN Interface Card

2 x PRI E1/T1 ISDN Network Interface
Cards on rear side
2 x Media Processing Cards in front

V.35 Serial Interface Card

2 x V.35 Serial Interface Cards on rear
side
2 x Media Processing Cards in front

Mix of Network Interface Cards

1 x PRI E1/T1 ISDN Network Interface
Cards on rear side
1 x V.35 Serial Interface Cards on rear
side
2 x Media Processing Cards in front

TANDBERG MPS 200

The TANDBERG MPS 200 has 3U-19” rack-mount-
able chassis.

There is support for up to 2 Network Interface

•

Cards in the software version J3 and above.

There can be a mix of Network Interface Cards

•

Network Interface Cards are installed in the

•

rear side of the chassis.

One Media Processing Board must be in front

•

of each Network Interface Card.

PRI E1/T1 ISDN Interface Card

You can install up to 2 PRI E1/T1 ISDN Interface
Cards.

The PRI E1/T1 ISDN Interface Cards are

•

installed in the rear of the chassis.

One Media Processing Board must be in front

•

of each ISDN Interface Card.

V.35 Serial Interface Card

You can install up to 2 V.35 Serial Interface
Cards.

The V.35 Interface Cards are installed in the

•

rear of the chassis.

One Media Processing Board must be in front

•

of each V.35 Interface Card.

Mix of Network Interface Cards

You can install a mix of PRI E1/T1 ISDN Interface
Cards and V.35 Serial Interface Cards.

The PRI E1/T1 ISDN Interface Card and the

•

V.35 Interface Card are installed in the rear of
the chassis.

One Media Processing Board must be in front

•

of each ISDN/V.35 Interface Card.

Network Interfaces

155

Introduction

Quick

Setup

Using

the MPS

System

Status

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Appendices

Main

Technical

Descriptions

Содержание Media Processing System MPS 800




















































































































































































Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды

TANDBERG Media Processing System MPS 800, Руководство администратора

Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды