TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 172

Страница: 172 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

RFC

The following current RFC’s and drafts are supported:

RFC 1889 RTP: A Transport Protocol for Real-time Applications

•

RFC 2190 RTP Payload Format for H.263 Video Streams

•

RFC 2327 SDP: Session Description Protocol

•

RFC 2396 Uniform Resource Identifiers (URI): Generic Syntax

•

RFC 2429 RTP Payload Format for the 1998 Version of ITU-T Rec.

•

H.263 Video (H.263+)

RFC 2617 Digest Authentication

•

RFC 2782 DNS RR for specifying the location of services (DNS

•

SRV)

RFC 2833 RTP Payload for DTMF Digits, Telephony Tones and

•

Telephony Signals

RFC 2976 The SIP INFO Method

•

RFC 3016 RTP Payload Format for MPEG-4 Audio/Visual Streams

•

RFC 3047 RTP Payload Format for ITU-T Recommendation

•

G.722.1

RFC 3261 SIP: Session Initiation Protocol

•

RFC 3262 Reliability of Provisional Responses in SIP

•

RFC 3263 Locating SIP Servers

•

RFC 3264 An Offer/Answer Model with SDP

•

RFC 3311 UPDATE method

•

RFC 3361 DHCP Option for SIP Servers

•

RFC 3420 Internet Media Type message/sipfrag

•

RFC 3515 Refer method

•

RFC 3550 RTP: A Transport Protocol for Real-Time Applications

•

RFC 3581 Symmetric Response Routing

•

RFC 3605 RTCP attribute in SDP

•

RFC 3711 The Secure Real-time Transport Protocol (SRTP)

•

RFC 3840 Indicating User Agent Capabilities in SIP

•

RFC 3890 A Transport Independent Bandwidth Modifier for SDP

•

RFC 3891 The SIP “Replaces” Header

•

RFC 3892 Referred-By Mechanism

•

RFC 3960 Early Media

•

Current RFCs and Drafts Supported

SIP - Current RFC’s and Drafts Supported

RFC 3984 RTP Payload Format for H.264 Video

•

RFC 4028 Session Timers in SIP

•

RFC 4145 TCP-Based Media Transport in the SDP

•

RFC 4566 SDP: Session Description Protocol

•

RFC 4568 SDP:Security Descriptions for Media Streams

•

FC 4574 The Session Description Protocol (SDP) Label Attribute

•

RFC 4582 The Binary Floor Control Protocol

•

RFC 4583 Format for Binary Floor Control Protocol (BFCP)

•

Streams

RFC 4585 Extended RTP Profile for RTCP-Based Feedback

•

RFC 4587 RTP Payload Format for H.261 Video Streams

•

RFC 4629 RTP Payload Format for ITU-T Rec. H.263 Video

•

RFC 4796 The Session Description Protocol (SDP) Content At-

•

tribute

draft-ietf-xcon-bfcp-connection-04.txt

•

draft-levin-mmusic-xml-media-control-08.txt

•

draft-ietf-sipping-cc-transfer-07.txt

•

draft-kristensen-avt-rtp-h264-extension-00.txt

•

172

Introduction

Quick

Setup

Using

the MPS

System

Status

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Main

Appendices

Содержание Media Processing System MPS 800




















































































































































































Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды

TANDBERG Media Processing System MPS 800, Руководство администратора

Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды