TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

Quick Setup

TANDBERG

MPS

ADMINISTRATOR GUIDE

Using the Web Interface

User Interfaces for the MPS

Web Interface

The TANDBERG MPS is normally controlled
via the web interface, but any authorized user
may schedule meetings on the TANDBERG
MPS by using the TANDBERG Management
Suite (TMS) or the TANDBERG Scheduler.

In this guide we will describe how to use the
web interface of the TANDBERG MPS.

The TANDBERG MPS consists of the
Multipoint Control Unit (MCU), and may also
include optional Gateway functionality.
Note that the Gateway Configuration tab on
the web interface is only visible when the
Gateway option is installed.

SSH and Telnet

The TANDBERG MPS can also be controlled
via SSH or Telnet by using a comprehensive
set of API commands. This enables the
TANDBERG MPS to be controlled by a different
user interface, such as an AMX or Crestron
control systems.



Start a Web browser and enter

the IP address of the MPS.

You can use either

http

or

https

,

with

https

recommended for

administrative access.

The

http

settings can be

configured after the first login.
See

System Configuration >

Miscellaneous Configuration



When prompted for login, enter the user

name

admin

and password,

TANDBERG

(default password).



The Overview page is the opening page

and you will see all conferences currently
active on the TANDBERG MPS.

Overview

The Overview page
lets you see informa-
tion about all confer-
ences currently active
on the TANDBERG
MPS.

MCU

Shows all MCU

•

conferences

GW*

Shows all Gateway

•

calls.

Phone Book

Use Phone Book to:

Add new entry

•

Edit existing entry

•

Dial out

•

Add up to 250

•

single entries

Add up to 16 group

•

entries.

System Status

Gives an overview of:

PRI Status

•

G.703 Status

•

V.35 Status

•

Media Board Infor-

•

mation

H.323 Status

•

SIP Status

•

System Informa-

•

tion

System Config.

Lets you configure:

H.320

•

PRI

•

G.703

•

IP

•

Media Board

•

Serial V.35

•

H.323

•

SNMP

•

SIP

•

QoS

•

Miscellaneous

•

Upgrade

•

Language

•

XML

•

Certificate Mgmt

•

Gateway Config.*

Lets you configure:

Dialling Rules

•

Settings

•

Files

•

MCU Configuration

Lets you configure:

Dial In Numbers

•

Network Profile

•

Conference Tem-

•

plate

Files

•

* Visible only when a Gate-
way is installed

For further information please see
the document

TANDBERG MPS API

or

http://www.tandberg.com

.

For the web interface of the TANDBERG MPS

to work properly, make sure you have
set the permission to ‘Allow Scripting’
in the Security Settings in the Web
browser.

User Interfaces for the MPS

31

Introduction

Using

the MPS

System

Status

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

Quick

Setup

«
...
29
30
31
32
33
...
»

Содержание Media Processing System MPS 800




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Processing System MPS 800

Бренд: K&G GROEP Страницы: 27

Бренд: Magnavox Страницы: 23

Бренд: Telefunken Страницы: 41

ControlLogix 1756-CNB

Бренд: Allen-Bradley Страницы: 36

Бренд: Hioki Страницы: 52

Бренд: FXConnectX Страницы: 14

Бренд: GE Страницы: 79

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 33

Бренд: MachMotion Страницы: 7

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 4

Бренд: Philips Страницы: 22

Бренд: Philips Страницы: 32

Бренд: Philips Страницы: 34

Бренд: jWIN Страницы: 16

administration and

Бренд: AT&T Страницы: 404

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды