TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

TANDBERG

MPS

ADMINISTRATOR GUIDE

Certificate Management

Certificate Management

Certificate Management

Manage Certificates

Allows an administrator to upload X.509 certificates for
use with HTTPS. These certificates can be created from
any trusted CA (Certificate Authority) to prevent possible
security warnings in the web browser due to the default self
signed certificate.

To install an HTTPS certificate, the following is needed:

The HTTPS certificate (.PEM format)

•

The Private key (.PEM format)

•

The Passphrase (optional)

•

NOTE

- Although a Passphrase is optional; if the certificate

was created using a passphrase then the passphrase must
be entered to make use of the certificate.

Browse

- Press the Browse button to locate the HTTPS certificate and Private key.

Upload

- Press the Upload button to upload the HTTPS certificate, Private key and Passphrase (if used).

NOTE

- The MPS must be restarted for the new certificate to take affect.

111

Introduction

Quick

Setup

Using

the MPS

System

Status

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Configuration

«
...
109
110
111
112
113
...
»

Содержание Media Processing System MPS 800




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Processing System MPS 800

Бренд: Xtrons Страницы: 11

PSS67 IO1 16FDI

Бренд: Pilz Страницы: 36

Бренд: ENTRYPASS Страницы: 42

Бренд: Polyaire Страницы: 20

Бренд: TANDBERG Страницы: 65

Бренд: Discount Car Stereo Страницы: 4

Бренд: Alpine Страницы: 2

Бренд: J&M Страницы: 8

Бренд: ZheJiang Libiao Robotics Страницы: 10

InfoView IV 2000

Бренд: InnoMedia Страницы: 50

Бренд: Aiwa Страницы: 28

Бренд: Alpine Страницы: 19

Polycom VSX 5000

Бренд: MBTelehealth Страницы: 14

TelePresence MCU 4505

Бренд: Cisco Страницы: 7

TelePresence MCU 4203

Бренд: Cisco Страницы: 6

TelePresence MX300

Бренд: Cisco Страницы: 2

IRIDIUM CERTUS 100

Бренд: Lars Thrane Страницы: 4

Бренд: Sanwa Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды