TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 35

Страница: 35 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

Initial Configuration (4:4)

Configuration of the MPS using Web Interface

Open a web browser and type in the IP address to
access the web interface. The IP address to enter
was configured from the LCD during the installation
process.

Dial In Configuration

Navigate to MCU Configuration > Dial In Numbers:

Configure one or more of the following numbers and
aliases to enable the MPS to know which confer-
ence number to dial into.

ISDN Number.

•

The ISDN number must be a valid

PRI number of the TANDBERG MPS at hand.

E.164 Alias.

•

The H.323 E.164 numeric alias for

each conference.

The

Single Dial In Number

allows the MPS to set

up multiple conferences, in an Ad Hoc manner by
the user dialling in to a single number.

You may configure and create different types
of conferences. Please refer to section

MCU

Configuration > Dial In Numbers

for details.

Simple Dial In Configuration

Save

- Press the Save button to save changes.

Simple Dial In Configuration



Introduction

Using

the MPS

System

Status

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

Quick

Setup

Содержание Media Processing System MPS 800




















































































































































































Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды

TANDBERG Media Processing System MPS 800, Руководство администратора

Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды