TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

TANDBERG

MPS

ADMINISTRATOR GUIDE

Upgrade

Software Upgrade

Software Upgrade

New software to the TANDBERG MPS can be installed via
the Software Upgrade web page.
The Software Upgrade page shows the current software ver-
sion, the hardware serial number and the installed options
and the option keys.

System Information - Software Version:

Shows the cur-

rently installed Software version.

System Information - Hardware Serial Number:

Shows the

unique hardware serial number of the TANDBERG MPS at
hand. The TANDBERG MPS serial number must be provided
when ordering a Software Upgrade.

System Information - Current Option Key:

Shows the cur-

rent installed Option Keys.

Software Option - Add Option Key:

Enter the option key in

the Key field and press ‘Add Option’. The system will validate
the key. When validated, feel free to add more option keys in
the same manner. However, to get the new options up and
running, the TANDBERG MPS must be restarted. Please use
the

Restart

button on the bottom of this page.

Install Software - Release Key:

Enter the release key in the

Key field and press ‘Install Software’. You will be presented
with a new page where you select the software package file
to upload.

V.35 Firmware Upgrade - Firmware Upgrade File:

Press

‘Browse’ to select the firmware upgrade file and press “In-
stall Firmware” to proceed with the firmware upload.

There are two different version of the TANDBERG
MPS software file. One standard software file
(

s41000jxx.tar.gz

), and one software file

(

s41001jxx.tar.gz

) without Encryption (without

AES and DES support).

For changes to take effect the unit must be restarted.

Restart

- Press the Restart button. This will restart the MPS.

Important - Before Upgrading

To upgrade the TANDBERG MPS, a valid Release Key
and Software file is required. Please contact your
TANDBERG representative for more info.

106

Introduction

Quick

Setup

Using

the MPS

System

Status

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Configuration

«
...
104
105
106
107
108
...
»

Содержание Media Processing System MPS 800




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Processing System MPS 800

Markoprint iJET

Бренд: Weber Страницы: 127

Бренд: Optimus Страницы: 44

Бренд: Yealink Страницы: 52

Бренд: Jensen Страницы: 3

Бренд: Yealink Страницы: 36

Бренд: HME Страницы: 2

Бренд: SoundMax Страницы: 43

Бренд: Grace Digital Страницы: 1

Бренд: Powerdist Страницы: 7

Бренд: Hama Страницы: 53

Бренд: Teufel Страницы: 24

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 28

VideoJet 400 19"

Бренд: VCS Страницы: 86

Бренд: Avalon Страницы: 86

Бренд: Cambium Networks Страницы: 16

Бренд: Curtis Страницы: 1

CONFERENCE MAX NDA-31109

Бренд: NEC Страницы: 5

Бренд: Dell Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды