TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 87

Страница: 87 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

H.320 Board

Slot (1 to n)

Select Slot

to configure the H.320 (ISDN) board(s). The

illustration shows that Slot 1 and 3 are configured for H.320,
while Slot 2, 4, 5 and 6 are not configured.

Network Configuration

Description

Enter a compulsory textual description to easier identify each
card.

Network Type

Select which type of H.320 (ISDN) network each of the ISDN
network cards are connected to:

PRI:

ISDN Line

G.703:

Leased line

PRI Board Configuration

Please ensure that

Network Type

is set to

PRI

for the

correct ISDN cards. This must correspond with the
Slots used in

PRI Board Configuration

Please ensure that

Network Type

is set to

G.703

for

the correct ISDN cards. This must correspond with the
Slots used in

G.703 Board Configuration

Press the

Save

button

to save changes

Introduction

Quick

Setup

Using

the MPS

System

Status

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Configuration

Содержание Media Processing System MPS 800




















































































































































































Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды

TANDBERG Media Processing System MPS 800, Руководство администратора

Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды