TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 107

Страница: 107 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

Language

Set Language

Select Web Interface Language

Select the desired Web Interface Language and press Set
to activate.

Language Configuration and File Management

Set Language

The Set Language allows you to view and change the lan-
guage in the web interface and dialogs.

Select Dialog Language

Select the desired Dialog Language and press Set to acti-
vate.

Type

When a customized file has been upload-

•

ed the text “Predefined file“ is replaced
with a Delete button.
When a customized file has been deleted

•

the Delete button is replaced with the
text “Predefined file“.

Browse

Press the Browse button
to find a file.

Upload

Press the Upload button
to upload the file.

File

Press the name of the
File on the left side of the
window to view or hear
the content of the file.

File Management

The File Management allows viewing and changing pictures,
sounds and symbols, which are shown to the participants
when connecting to, and during a conference on the MPS.

Different files can be uploaded for different lan-
guages. If you want to use files that are language
independent, please see

File Management

in the

MCU Configuration section.

Web Interface

The following web interface options can be specified:

Language - Upload language file (MCU & GW).

•

Value Space - Upload Value Space file (MCU & GW).

•

Both files should be uploaded for a given language.

To add a new file, press

Browse

to find the file, and then

press

Upload

. For each customized file, a

Delete

button will

be added in the Type column.

Manage Files for Language

Select the desired language for managing language depen-
dent files only. Press the

Manage

button to activate.

107

Introduction

Quick

Setup

Using

the MPS

System

Status

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Configuration

Содержание Media Processing System MPS 800




















































































































































































Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды

TANDBERG Media Processing System MPS 800, Руководство администратора

Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды