TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

TANDBERG

MPS

ADMINISTRATOR GUIDE

Cascaded MPS

The TANDBERG MPS supports two-level cascading, so the
TANDBERG MPS can be cascaded with other TANDBERG MPSs
to increase the number of participants in one conference.
By simply dialling from one TANDBERG MPS to other TANDBERG
MPSs one will achieve a distributed setup.
In this case the TANDBERG MPS dialling out will be defined as
the master MCU and all other MCUs as slaves.
The connection between the MCUs (or the Endpoints) can be IP,
ISDN or V.35.

The slave MCUs will automatically be set to Voice
Switched while the master MCU may be set to one of the
CP layouts or kept in Voice Switched mode.

A distributed MCU scenario may add delays to the switch-
ing of conference.

Cascaded MPS

Features supported within a distributed MCU scenario:

DuoVideo

•

TF

from any site

Encryption (as long as all sites support this feature)

•

Request Floor from any site

•

View Site naming (of any site in the conference)

•

Administrator features (on TANDBERG MPS or TMS):

View site names (terminal list) of all participants

•

Configure the conference as Master, Slave or Auto

•

Auto – The MCU dialling out will become Master

•

Master/Slave status on Web

•

Conference Layout disabled on Slave MCU

•

Assign Floor from Master MCU

•

Shows the site in full screen for all participants

•

Assign Floor from Slave MCU

•

Shows the site in full screen for all participants

•

Only to sites on this MCU

•

Administrator Features Supported

Features Supported

Features

Distributed MCUs

!

161

Introduction

Quick

Setup

Using

the MPS

System

Status

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Appendices

Main

Technical

Descriptions

«
...
159
160
161
162
163
...
»

Содержание Media Processing System MPS 800




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Processing System MPS 800

FUSION Apollo MS-WB670

Бренд: Garmin Страницы: 44

Бренд: iHome Страницы: 17

Бренд: WAGNER Страницы: 128

Бренд: Coby Страницы: 1

Бренд: Jensen Страницы: 3

COLLABORATE Room

Бренд: ClearOne Страницы: 48

Бренд: Teufel Страницы: 16

Бренд: Panasonic Страницы: 22

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 33

Бренд: Panasonic Страницы: 15

Бренд: Looperlative Страницы: 29

Бренд: Chrosziel Страницы: 2

MERLIN LEGEND Release 6.0

Бренд: Lucent Technologies Страницы: 160

E84DGFCR Series

Бренд: Lenze Страницы: 93

Бренд: Hitachi Страницы: 44

Бренд: Advanced Native Technologies Страницы: 29

Бренд: Lexicomm Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды