TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

Gateway Configuration

TANDBERG

MPS

ADMINISTRATOR GUIDE

When receiving a call with the Gateway configured
with only one number in the PRI number range, all
other incoming calls will be blocked until the ongoing
call is established.
This is because the network will have no additional
number available for the second call while setting up
the call.
When the call is established the number will be avail-
able and any incoming call will connect as normal.

Gateway Configuration (1:3)

Interoperability

Experience has shown that some features - even though
they are standardized - might cause interoperability prob-
lems with legacy video conferencing products.
By disabling features on this page, the Gateway can be used
as a filter to ensure interoperability with legacy products.

Gateway Configuration

Natural Video
On:

Set to On to allow video formats and capabilities such

as interlaced video (iCIF/iSIF) to be transmitted through the
Gateway.

Off:

When set to Off no interlaced video capabilities will be

transmitted.

Dual Video Stream (DuoVideo

TF

/H.239/BFCP)

On:

Set to On to allows an additional video stream to be

transmitted through the gateway using DuoVideo

TF

or the

H.239 or BFCP protocols.

Off:

When disabled no DuoVideo

TF

, H.239 or BFCP capabili-

ties will be transmitted.

Custom Video Formats
On:

Set to On to allow H.263 custom video formats and

capabilities such as SIF, 4SIF and VGA resolution to be
transmitted through the gateway.

Off:

When set to Off no H.263 custom video formats or

capabilities will be transmitted.

Save

- Press the Save button to save changes.

Restart

- For the settings to take effect the unit must be restarted after pressing the Save button.

118

Introduction

Quick

Setup

Using

the MPS

System

Status

System

Configuration

Installation

MCU

Configuration

Technical

Descriptions

Appendices

Main

Gateway

Configuration

«
...
116
117
118
119
120
...
»

Содержание Media Processing System MPS 800




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Processing System MPS 800

Бренд: Saito Страницы: 90

Бренд: N-Com Страницы: 2

Бренд: TCS Страницы: 16

Бренд: Teac Страницы: 3

Бренд: GE Страницы: 40

Бренд: Jensen Страницы: 13

IntelliGate 2025

Бренд: Aastra Страницы: 71

Бренд: Teac Страницы: 23

Бренд: Alpine Страницы: 133

RealPresence Centro

Бренд: Polycom Страницы: 53

Бренд: Tarfire Страницы: 31

Бренд: FXConnectX Страницы: 14

Бренд: iWantit Страницы: 32

Бренд: Samsung Страницы: 69

Бренд: Blaupunkt Страницы: 63

Бренд: auna Страницы: 68

Pilot Lite V1522

Бренд: Vicon Страницы: 138

Бренд: JVC Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды