TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

TANDBERG

MPS

ADMINISTRATOR GUIDE

PRI Board

Network Configuration

E1/T1 Interface Configuration

E1 CRC4

Used for most E1-PRI configurations.

On:

If set to On, the E1 CRC4 is enabled.

Off:

If set to Off, the E1 CRC4 is disabled. If your network

equipment does not support this feature, turn it Off.

T1 Cable Length

Specifies the cable length between the TANDBERG MPS and
the CSU for each of the PRI lines (only valid for T1 networks).
Possible values are:

Range1: 0 to 133 feet

•

Range2: 133 to 266 feet

•

Range3: 266 to 399 feet

•

Range4: 399 to 533 feet

•

Range5: 533 to 655 feet

•

This section configures each of the E1/T1 interfaces individu-
ally. There is one column for each interface (IF1, IF2,IF3, etc).
However, if PRI Trunk Groups is enabled, the number range
for PRI 1 will also apply for all the enabled PRI interfaces on
the same E1/T1 Interface Card.

Save

- Press the Save button to save changes.

E1/T1 Interfaces

- continued: PRI Board Configuration

94

Introduction

Quick

Setup

Using

the MPS

System

Status

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Configuration

«
...
92
93
94
95
96
...
»

Содержание Media Processing System MPS 800




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Processing System MPS 800

Бренд: JBL Страницы: 8

Бренд: Cyrus Страницы: 6

Бренд: Velux Страницы: 11

magicbox aavelin

Бренд: ClearOne Страницы: 93

Бренд: Nakamichi Страницы: 12

MFIT MERCEDES SPRINTER W907 EVO 2

Бренд: Audio System Страницы: 2

Бренд: Coby Страницы: 1

Бренд: Rath Страницы: 7

Бренд: ICON Страницы: 6

eyespeak zuvo 12-D

Бренд: Talk To Me Technologies Страницы: 28

Бренд: AVer Страницы: 107

Audio 30 Export 3301

Бренд: Becker Страницы: 92

Бренд: EMX Industries, Inc. Страницы: 19

Бренд: Vahle Страницы: 100

Бренд: Exibel Страницы: 32

Бренд: Panasonic Страницы: 172

Бренд: Sanyo Страницы: 16

Бренд: Sanyo Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды