D 13373.08
NOVEMBER 2007
MPS
Gateway Configuration
TANDBERG
MPS
ADMINISTRATOR GUIDE
The J3 software and above supports
H.323 to V.35 Gateway.
Example with DID:
You would like to have a DID number from
H.323 to a V.35 port.
Add Dialling Rule
Set
1.
Type
to
DID
Select
2.
Bandwidth
Set
3.
Number of Significant Digits
to empty
or to
0
(zero)
Set
4.
From Network Type
to
H.323
Set
5.
From Prefix
to
9
Set
6.
To Network Type
to
V.35
Leave
7.
To Prefix
empty
To call a V.35 port 1 on module card 1, would
require you to dial 90101 from the H.323
endpoint.
Configure Incoming V.35 Gateway
It is also possible to configure an incoming
V.35 gateway.
This can be setup as a V.35 DID or a V.35
•
IVR service.
In the case of setting up an IVR service,
•
make sure that your V.35 peripheral equip-
ment supports DTMF relaying.
V.35 Ports
To address the V.35 ports in a dialling rule,
the physical V.35 ports have a numeric
representation with two digits for each the
interface number and module number.
Make sure that this string always contains 4
digits.
Range will therefore be 0101 to 0632 for cor-
responding V.35 cards/modules in slot 1 port
1 to slot 6 port 32.
Example:
Slot 1 & Port 1: 0101
Slot 1 & Port 2: 0102
Slot 1 & Port 3: 0103
....
Slot 1 & Port 30: 0130
Slot 1 & Port 31: 0131
Slot 1 & Port 32: 0132
Slot 12 & Port 1: 0601
Slot 12 & Port 2: 0602
Slot 12 & Port 3: 0603
....
Slot 12 & Port 30: 0630
Slot 12 & Port 31: 0631
Slot 12 & Port 32: 0632
Examples with V.35 Gateway
Example with DID (V.35 to H.323)
You would like to have a DID number from a
V.35 port to a specific H.323 endpoint.
Add Dialling Rule
Set
1.
Type
to
DID
Select
2.
Bandwidth
Set
3.
Number of Significant Digits
to empty
Set
4.
From Network Type
to
V.35
Set
5.
From Prefix
to
0102
Set
6.
To Network Type
to
H.323
Set
7.
To Prefix
to
55013
Make sure the
Bandwidth
selected matches
the bandwidth of the V.35 port.
This would set up a Gateway call between the
V.35 0102 port, to the H.323 endpoint, with
alias 55013.
It is recommended not to use the same
V.35 port for MCU calls and for Gateway
calls because the support for incoming
V.35 Gateway might conflict with the
MCU V.35 setup.
The Gateway does only support H.320
to H.323 Gateway calls. There is no
functionality to support Gateway routing
internally within H.320 protocols (ISDN,
V.35 and Leased Line).
It is recommended to set DTR pulse to
On in the Serial V.35 configuration page
for each port to be used for V.35 to
H.323 Gateway calls.
Example 1: DID
Example 3: DID
Example 2: DID
About V.35 Ports
Example with DID:
You would like to have a DID number from
H.323 to a specific V.35 card.
Add Dialling Rule
Set
1.
Type
to
DID
Select
2.
Bandwidth
Set
3.
Number of Significant Digits
to empty
Set
4.
From Network Type
to
H.323
Set
5.
From Prefix
to
9
Set
6.
To Network Type
to
V.35
Set
7.
To Prefix
to
01
To call V.35 port 4 on the already defined
module card 1 would require you to dial 904
from the H.323 endpoint.
The To Prefix of 01 defines the use of
Network Module 1 so this does not
need to be included in the H.323 dial
string.
For further information about how the
video system endpoint supports TCS-4
please see the MXP Administrator’s
Guide on
.
116
Introduction
Quick
Setup
Using
the MPS
System
Status
System
Configuration
Installation
MCU
Configuration
Technical
Descriptions
Appendices
Main
Gateway
Configuration
