Tadano GR-1600XL Скачать руководство пользователя страница 97

Страница: 97 / 269

Y-9

Operation Check (Traveling Device)

WY05-5040E

9. Hydraulic suspension

9.1 Normal operation

Check the suspension state and the suspension lock indicator with the following procedure.

Operation

Suspension lock indicator

Suspension state

Turn ON the main switch to start

engine.

↓

Keep pressing the suspension

free switch for 1 second or more.



Check that the suspension emergency free switch

is on the normal position and put the vehicle into a

traveling state while the boom is in a front-side.

Flashes slowly during leveling.
Goes out after leveling.

Free after leveling
(Normal traveling starts)

↓

Suspension up/down switch



Leveling is impossible when the road surface is not flat.

In this case, adjust to the lock state by operating the suspension

up/down switch, move to a flat ground, and then operate the

suspension free switch again.

Operate in the following order.
1. Down operation ....... Flashes

(20 seconds or less) slowly

2. Up operation ............ Flashes

slowly

3. Down operation ....... Lights up

(20 seconds or over)

Locked after vehicle height is

lowered

Locked after vehicle height is

raised

Locked after suspension is fully

retracted.



Vehicle height is raised or lowered while the switch is being pressed.

The vehicle height is locked when the operation switch is released.

↓

Turn ON the PTO switch.

Check that the operation status is

on-rubber status on the AML.

Suspension lock indicator:

Lights up
Operation condition: On-rubber

Locked after suspension is fully

retracted.

↓

Turn OFF the PTO switch.

Keep pressing the suspension

free switch for 1 second or more.

Flashes slowly during leveling.

Goes out after leveling.

Free after leveling

(Normal traveling starts)

↓

PTO - ON

Flashes slowly

Locked

↓

Flashes slowly: 0.8 second interval, Flashes fast: 0.4 second interval

Содержание GR-1600XL














































































































































































































































































Результаты поиска

Содержание GR-1600XL

Отзывы:

Похожие инструкции для GR-1600XL

Бренды по названию

Популярные бренды

Tadano GR-1600XL, Руководство по обслуживанию

Результаты поиска

Содержание GR-1600XL

Отзывы:

Похожие инструкции для GR-1600XL

Бренды по названию

Популярные бренды